manualshive.com logo in svg

MUTOH VJ-1638UH Mark II, Installation Manual

Share
Download
MUTOH VJ-1638UH Mark II Installation Manual Download Page 1

 

1 

VJ1638UH2E-I-02

VJ-1638UH Mark

Ⅱ

 INSTALLATION MANUAL

Please read this manual 
before using

Installation flow chart

1 

Unpacking boxes

3 

Assembling

5 

Connecting the power cable

6 

Turning the power ON/OFF

7 

Product activation

8 

Initial ink charging

9

 

Loading media

9.1 

Loading rigid media

9.2 

Loading roll media

8.1 

Installing the cleaning wiper

8.2 

Initial ink charging

10 

Checking the print condition

11 

Manual composition

3.1 

Assembling the stand

3.2 

Attaching the stand

3.3 

Detaching fastening materials

3.4 

Assembling the Media-feed table

 (optional)

4 

Installation

4.1 

Installation environment

4.2 

Installation procedure

2 

Confirming bundled items

2.1 

Items in the printer box

2.2 

Items in the accessory box

2.3 

Items in the stand box

2.4 

Items in the Media-feed table 
(optional) box

1.1 

Unpacking the printer box

1.2 

Unpacking the stand box and 
the Media-feed table F and R 
boxes

Thank you for purchasing a MUTOH product.

This manual explains the steps for unpacking, 
mounting and basic installation before using the 
MUTOH Full-color inkjet printer VJ-1638UH Mark

Ⅱ

.

This manual is intended for owners, installers, and 
users of this product.

Understand the contents and instructions in this 
manual before installing this product.

The broad steps for installation are shown below.

There are instructions for each section beginning on 
the next page.

Summary of Contents for VJ-1638UH Mark II

















Reviews:

No comments

Brands by name

Popular brands

Load more brands