background image

 

 

 

Ver. 1.05

 

 

 

Maintain 

tools

, keep them clean.

 

 

Do NOT attempt to insert a cutting knife with your fingers, as you will cut yourself with the razor sharp 

edges of these blades.

 

 Use needle nose pliers to insert and remove blades.

 

 

Check for misalignment or binding of moving parts, breakage

 

of parts, and 

any 

other condition that 

may affect the tools

 

operation.  If damaged, have the tool serviced before using.

 

Poorly maintained tools 

cause many accidents.

 

 

Use only accessories and screws that are recommended by

 Muro

 for your model. 

Accessories that may 

be suitable 

for one tool, may become hazardous when used on another tool.

 

 

Keep your tool clean; remove dust and dirt by vacuuming or carefully blowing out regularly. Other t

ool 

service  must  be  performed  only  by  qualified  repair

 

personnel: 

Service  or  maintenance  performed  by 

unqualified 

personnel could result in a risk of injury. Use of unauthorized parts or failure to follow these

 

Instructions may create a risk of electric shock or injury.

 

 

Additional Safety Rules

 

 

Hold tool by insulated gripping surfaces

 when performing an operation where the screws may contact hidden wiring 

or its own cord.  Contact with a “

live

” wire will make exposed metal parts of the tool "

live

" and shock the operator if in 

contact.  Keep handles in good condition, dry, clean, free from oil and grease.  It is recommended to use rubber gloves; 

this will enable better control and safety.  Replace handle grips if worn.

 

 

DO NOT TOUCH ANY METAL PARTS OF THE TOOL when

 

drilling or driving 

into 

walls, floors or wherever live 

electrical

 

wires may be encountered.  

Hold the tool only by insulated grasping surfaces to prevent electric shock if 

you drill or drive into a live wire.

 

 

CH7390 Operating Instructions.

 

 

The CH7390 Ultra Driver will fit many of the popular screwgun/screwdriver tools with a depth sensitive clutch.  The 

CH7390  is  attached  to  a  screwgun  by  using  the  adaptor  for  the  specific  brand  and  model  of  screwgun.    Highly 

recommended  for  2  ½  and  3  inch  fasteners  and  general

-

purpose  use  is  the  Makita  2200  “quiet  clutch”  duty 

framing/deck screwgun.  The DeWalt DW276 Heavy duty framing/deck screwgun is also highly recommended.  They 

are geared for the high torque requirements of longer screws or harder wood.  In very soft wood and with short screws 

or for drywall applications the higher speed models may be preferable such as the Makita 4200, Porter Cable 6640 or 

the DeWalt 274. 

 

 

Attach  the  adaptor  to  your  screwgun  screwdriver  carefully  using  the  instruction  sheet  that  comes  with  the  adaptor.  

Make sure internal clutch pins and springs are placed back together properly to prevent damage.  

 

 

 

Summary of Contents for VISLIDER CH7390 Ultra Driver










Reviews: