background image

 

A152-VR-BF4

Page 15 of 20

Date: 

10/28/2020

7021-023-001

MURDOCK  MFG.  • 

15125  Proctor  Avenue  •  City  of  Industry,  CA  91746  USA 

Phone  800-453-7465  or  626-333-2543  •  Fax  626-855-4860  •  www.murdockmfg.com

Member of

PUSH-IN FITTING INSTALLATION

NOTE: FITTINGS AND TUBE SHOULD BE KEPT 
CLEAN, BAGGED AND UNDAMAGED PRIOR 
TO INSTALLATION.

2. Pull on the fitted tubing to ensure it is secure. 

Tube should not come free from the fitting. Water 
test the connection assembly prior to leaving the 
site to ensure there are no leaks.

DISCONNECTING THE TUBE:

To disconnect the tube from the fitting ensure that 
the water line is depressurized. Push collet square 
towards the push-in fitting body and hold. While 
holding the collet in, pull on the PE tubing to remove 
from the push-in fitting. 

TO CUT TUBE:

Cut to fit length of 1/4” PE tubing and remove any 
burrs or sharp edges. Ensure that the outside 
diameter is free from score marks. Tube ends 
should be square.

1.   Firmly and fully insert the tubing end into the 

push-in fitting up to the tube stop located 
approximately ½” deep.

INSERTING THE TUBE:

COLLET

COLLET

O-RING

O-RING

TUBE STOP

COLLET

COLLET

COLLET

CONTEMPORARY WATER COOLERS

 

I N S TA L L AT I O N / M A I N T E N A N C E  I N S T R U C T I O N S

 DRINKING FOUNTAINS

 

Summary of Contents for A152-VR-BF4 Series





















Reviews: