Munters WM36 Instruction Manual Download Page 32

Page: 32 / 36

QM1077r16

7.1 Troubleshooting

Troubleshooting

Fan Operating-
Insuﬃ cient Airﬂ ow

Excessive
Vibration

Excessive Noise

1. Fan control set above room
temperature
2. Blown fuse or open circuit breaker
3. Propeller blade contacting fan housing
4. Fan control defective
5. Motor defective

1. Damper door jammed
2. Guard dirty

1. Propeller blade contacting fan housing

1. Motor loose on mount
2. Propeller damaged
3. Motor or propeller shaft bent

1. Set to a lower temperature

2.  Replace fuse or reset breaker
3.  Realign propeller in fan housing
4.  Repair or replace control
5.  Repair or replace motor

1. Clean damper door & fan housing
2. Clean guard

1. Sand fan housing to remove high spot

1. Tighten fasteners
2. Replace propeller
3. Repair or replace motor or propeller shaft

Fan Not Operating

SYMPTOM

POSSIBLE CAUSES

CORRECTIVE ACTION

Fan Never Turns Off

1. Override thermostat set incorrectly
2. Control set for continuous operation

1. Set to the correct temperature
2. Set control correctly

WARNING

Disconnect Power

Before Servicing

WARNING

Moving Parts, Disconnect

Power Before Servicing.

WARNING

Moving Parts: Disconnect

Power Before Servicing.

Summary of Contents for WM36





































Search results

Summary of Contents for WM36

Reviews:

Related manuals for WM36

Brands by name

Popular brands

Munters WM36, Instruction Manual

Search results

Summary of Contents for WM36

Reviews:

Related manuals for WM36

Brands by name

Popular brands