Munters WM36 Instruction Manual Download Page 10 | Manualshive

Page: 10 / 36

background image

© Munters Corporation, August 2021

10

QM1077r16

Step 5

Place Orifice Panel on saw horses with the round orifice pointing up and place (1) Cone/Strut Mounting
Bracket in each corner of the Orifice Panel.

See Figure 5.

Mounting Bracket

Oriﬁ ce Panel

Step 6

Corners of Orifice Panel with 2 holes are corners where Strut Assembly attaches. Secure Strut Assembly using
(4) Long Bolts [CC], (6) Washers [EE] and (4) Nuts [DD]. In the opposite corners attach Cone/Strut Mounting
Bracket to the orifice using (1) Short Bolt [AA], Washer [EE] and Nut [DD].

See Figure 6.

Figure 5

Figure 6

Long Bolt [CC]

Washer [EE]

Washer [EE]

Nuts [DD]

Drain Hole

Washer [EE]

Short Bolt [AA]

Nuts [DD]

Installation Instructions

Chapter 2

«
...
8
9
10
11
12
...
»

Summary of Contents for WM36





































Reviews:

No comments

Related manuals for WM36

Brand: HAMPTON BAY Pages: 13

Brand: UltimateAir Pages: 3

Brand: JetBlack Pages: 20

Brand: ProKlima Pages: 100

Brand: Parrot Uncle Pages: 4

SlotVent 2500EA

Brand: Yale Pages: 6

Brand: NOMA Pages: 13

Brand: Xpelair Pages: 56

KLOUT FP3070 Series

Brand: Fanimation Pages: 40

Punto Filo MF 100

Brand: Vortice Pages: 17

Brand: UFESA Pages: 56

Brand: Fantech Pages: 4

Brand: Emerson Pages: 20

Brand: Emerson Pages: 16

Brand: Emerson Pages: 20

Brand: Emerson Pages: 20

Brand: Emerson Pages: 16

Brand: Emerson Pages: 13

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands