manualshive.com logo in svg

Munters Vortex VX26F1CP, User Manual And Installation Manual, Page: 12 / 15

Share
Download
Munters Vortex VX26F1CP User Manual And Installation Manual Download Page 12

FORM:  QM1070

Rev.3, February 2010 

Page 12 of 15

Munters Corporation

4215 Legion Dr.  Mason, MI  48854-1036  USA

(517) 676-7070    Fax (517) 676-7078

www.munters.us/aerotech   

TROUBLE SHOOTING

Fan Operating-

Insufficient

Airflow

Excessive Fan

Vibration

Excessive Fan 

Noise

1. Fan control set above room

    temperature
2. Blown fuse or open circuit breaker

3. Propeller blade contacting fan  

 

    housing

4. Fan control defective
5. Motor defective

1. Variable speed control improperly

    adjusted
2. Shutter jammed

1. Variable speed control idle speed

    set to low
2. Variable speed control defective

3. Propeller blade contacting fan panel
4. Motor bearing defective

1. Motor loose in mount
2. Propeller damaged
3. Motor shaft bent

Set to a lower temperature

Replace fuse or reset breaker
Realign motor in fan housing

Repair or replace control
Repair or replace motor

See Operation, Step 2 for 

adjustment guidelines
Clean shutter & fan housing
Clean guard

Increase idle speed setting

Repair or replace control
Realign motor in fan housing
Repair or replace motor

Tighten fasteners
Replace propeller
Repair or replace motor

Fan Not Operating

SYMPTOM

POSSIBLE CAUSES

CORRECTIVE ACTION

3. Guard dirty

WARNING

!

High Voltage,

disconnect power 

before servicing.

WARNING

!

Moving parts,

disconnect power 

before servicing.

Fan never turns off

1. Override thermostat set  

 

  incorrectly

2. Control set for continuous    

  operation

Set to the correct temperature

Set speed control correctly

Summary of Contents for Vortex VX26F1CP
















Reviews:

No comments