background image

22

16

.   

 

TEST OPERATION

The test operation must be carried out after the entire installation 
has been completed.

Please confirm the following points before the test operation:

The indoor unit and outdoor unit are installed properly.

Tubing and wiring are correctly completed.

The refrigerant pipe system is leakage-checked.

The drainage is unimpeded.

The heating insulation works well.

The ground wiring is connected correctly.

The      length   of      the    tub in  g and      the     added     stow      capacity      of     the     refriger-
ant have been recorded.

The power voltage fits the rated voltage of the air conditioner.

There is no obstacle at the outlet and inlet of the outdoor and 
indoor and indoor units

The gas-side and liqid-side stop vaule are both opened.

The air conditioner is pre-heated by turning on the power.

According to  the user’s  requirement, install  the  remote controller 
frame where the remote controller’s signal can reach the indoor 
unit smoothly.

Test operation
Set the air conditioner under the mode of “COOLING”with the 
remote controller, and check the following points per the “Owner’s   
Manual” If there is any malfunction, please resolve it through 
chapter “Troubles And Causes ”in the “Owner’sManual”.

The indoor unit 

Whether the switch on the remote controller works well.

Whether the buttons on the remote controller works well.

Whether the air flow louver moves normally.

Whether the room temperature is adjusted well.

Whether the indicator lights normally.

Whether the temporary buttons works well.

Whether the drainage is normal.

Protection function will delay the startup of compressor for 3 
minutes in case the unit is  turned on immediately after power 
on or restarted after shutdown.

CAUTION

Whether there is vibration or abnormal noise during operation.

W h e t h e r  t h e  a i r  c o n d i t i o n e r  h e a t s  w e l l  i n  t h e  c a s e  o f  t h e 
HEATING/COOLING type.

The outdoor unit

Whether there is vibration or abnormal noise during operation.

Whether the generated wind, noise, or condensed water by the 
air conditioner have influenced your neighborhood.

Whether any of the refrigerant is leaked. 

Installation manual

High pressure duct

Summary of Contents for CL23380

























Reviews: