background image

maintenance of motor

˖

Install indoor unit drain pipe
The outlet has PTI screw bread, For  71 to 160 indoor unit,
please use  sealing materials and pipe sheath (fitting) when 
connecting PVC pipes. For  200 to 280 indoor unit, please
use Water connecting pipe  

and  Adhesive tape for seal 

when connecting 

drain pipes.

      

10.   CONNECT THE DRAIN PIPE

All the stop valves should be opened before test operation. 
Each air conditioner has two stop valves of different sizes on 
the  side  of the outdoor unit which  operate s Lo-stop  value, 
respectively. (Refer to 

Fig.9-6

)

Flare nut

Stopper

Cap

Valve body 

Valve stem 

Fig.9-6

Fig.9-5

-76 cmHg

Lo-lever

Hi-lever

Charge hose

Charge hose

Vacuum pump

Lo-lever

Manifold valve

Multi-meter

Pressure meter

The necessary filling amount of refrigerant  

Refrigerant volume to be added is calculated according to 
outdoor unit installation manual .Be sure to add refrigerant 
measuring by a scale. L: The length of the pipe

Please record the quantity added and store it carefully for 
future maintenance.

Expel the air with a vacuum pump (Refer to 

Fig.9-4

) (Please 

refer to its manual for the way of using manifold valve)

Loosen and remove the maintenance nuts of stop valves A 
and B, and connect the charge hose of the manifold valve 
with the maintenance terminator of stop valve A.  (Be sure 
that stop valves A and B are both closed)

Connect the joint of the charge hose with the vacuum pump.

Open the Lo-lever of the manifold valve completely.

Turn on the vacuum pump. At  the beginning of pumping, 
loosen the maintenance terminator nut of stop valve B a little 
to check whether the air comes in (the sound of the pump 
changes, and the indicator of compound meter turns below 
zero). Then fasten the nut.

When the pumping has finished, close the Lo-lever of the 
manifold valve completely and turn off the vacuum pump.

When you have pumped for over 15 minutes, please confirm 
that the indicator of  multimeter is on  -1.0X105Pa (-76cmHg)

Loosen  and remove the quadrangle cover of stop valves A 
and B to open stop valve A and B completely, then fasten 
them.

Disassemble the charge hose from the repair-mouth of stop 
valve A, and  fasten the nut.

0 1 2

F

3

E

4

D

5

C

6

B

7

A

89

Bend

S shap

The drain pipe of indoor unit must be heat insulated, or it will 
condense dew, as well as the connections of the indoor unit.

Hard PVC binder must be used for pipe connection, and make 
sure there is no leakage.

With the connection part to the indoor unit, please be noted not 
to impose pressure on the side of indoor unit pipes.

When the declivity of the drain pipe downwards is over 1/100, 
there should not be any winding.

The total length of  the drain pipe when pulled out traversely 
shall not exceed 20m.

Refer to the figures on the right for the installation of the pipes. 

CAUTION

Fig.10-1

1.5M~2M

The height difference between drain pipe end to ground or drain 
channel should be more than 50mm, and the drain pipe cannot 
put in water. If the drain water was discharged to ditch directly, 
the drain pipe must be upward bent into a U type water seal to 
avoid odor into the interior through the drain pipe.

If the negative pressure of drain pan outlet is high, there must 
be a water elbow in drain pipe to avoid poor drain or blow water 
for negative pressure. Please install the water elbow as figure 
4.4 shown, each unit should install a water elbow. There should 
be a plug in water elbow for convenient cleaning. 

Installation manual

15

High pressure duct

Fig.10-2

Put as deep as possible
 (about 10mm)

Downward declivity
lower than 1/100

VP30

Fig.10-3

Indoor unit

H: 2''(50mm) or more.

+

+

Summary of Contents for CL23380

























Reviews: