manualshive.com logo in svg

Multitech MultiFRAD FR220, User Manual, Page: 2 / 103

Share
Download
Multitech MultiFRAD FR220 User Manual Download Page 2

User Guide

88310350 Revision A

MultiFRAD (Models FR220 and FR220/V2)

This publication may not be reproduced, in whole or in part, without prior expressed written permission from
Multi-Tech Systems, Inc. All rights reserved.

Copyright © 1999, by Multi-Tech Systems, Inc.

Multi-Tech Systems, Inc. makes no representations or warranties with respect to the contents hereof and
specifically disclaims any implied warranties of merchantability or fitness for any particular purpose.
Furthermore, Multi-Tech Systems, Inc. reserves the right to revise this publication and to make changes from
time to time in the content hereof without obligation of Multi-Tech Systems, Inc. to notify any person or
organization of such revisions or changes.

Record of Revisions

Revision

Description

       A

Manual released; covers software revision 3.00.  All pages at revision A.

(5/19/99)

PATENTS

This Product is covered by one or more of the following U.S. Patent Numbers:  

5.301.274; 5.309.562;

5.355.365; 5.355.653; 5.452.289; 5.453.986. Other Patents Pending.

TRADEMARK

Trademark of Multi-Tech Systems, Inc. are MultiFRAD and the Multi-Tech logo.

Windows is a registered trademark of Microsoft.

Multi-Tech Systems, Inc.

2205 Woodale Drive

Mounds View, Minnesota 55112

(612) 785-3500 or (800) 328-9717

Fax 612-785-9874

Tech Support (800) 972-2439

Internet: 

http://www.multitech.com

Summary of Contents for MultiFRAD FR220








































































































Reviews:

No comments