MULTIQUIP GLOBUG GB12BP, Operation And Parts Manual

Page: 34 / 45

PAGE 34 — GLOBUG LIGHTING SYSTEM — OPERATION AND PARTS MANUAL — REV. #2 (11/03/08)
GB12BW/BS/BP LIGHTING SYSTEM — NAMEPLATE AND DECALS
A
LW
A
Y
S
h
o
o
k
th
e
lat
ch
to
pr
e
v
ent
tipping.
Lower
position
Upper
position
GB12BS
GB12BW
LA M P IN FO R M ATIO N
CAUTION
NE VE R allow the lam p to strike any
hard surface. Excessive im pact can
cause dam age and reduce the service
life of the lam p.
GB12BP
DANGER
To avoid accident or
injury ALWAYS make
certain hardware is
securely fastened on
pipe clamps.
DCL1002
DANGER
To avoid accident or
injury ALWAYS make
certain hardware is
securely fastened on
pipe clamps.
DCL1002
DANGER
ELECTRICAL SHOCK HAZARD
DANGER
When replacing lamp and to prevent electrical shock,
ALWAY S shutdown the generator before replacing lamp.
Remember to let lamp cool before removing. Use only
recommended type lamp as listed in parts manual.
LAMP BURN HAZARD
WARNING
To prevent burns, NEVER touch lamp
while lamp is on. Lamp surface gets
extremely hot! ALWAYS allow sufficient
time for lamp to cool down before touching.
H IG H VO LTA G E (E -B A L L A S T )
DANGER
T he electronic com ponents of the ballast
generate high voltage.
NE V E R perform
m aitenance on the e-ballast w hen
connected to a pow er source.
DCL1261
DCL1263
WARNING
Keep clear of
pinch-point when
lowering the mast.
DANGER
CAUTION
WARNING
GloBug
INFORMATION
ALWAYS turn OFF generator
before performing maintenance.
NEVER disconnect
the GloBug Solo Jr.'s
connector when power
is applied.
The possibility exists
of Electrical shock or
equipment damage.
To prevent tipping, NEVER use
in winds that exceed 16 mph
( 7 m/ sec).
NEVER use on an incline of 5
degrees or more. The possibility
of tipping exists.
Pull tripod downward at the tip
end. Put sandbags on tripod to
improve the stability.
NEVER lift the GloBug Solo Jr.
Tighten T-handle bolt securely.
ALWAYS use the GloBug Solo
Jr.'s balloon on the top of mast.
NEVER operate the GloBug Solo
Jr. in the rain. A electrical shock
could occur causing Severe
Bodily Harmor even Death.
NEVER grab or touch
a live power cord
with wet hands,
the possibility exists
of Electrical shock,
Electrocution and
even Death!
To prevent burns, NEVER touch
ballast or cover while lamp is on.
These surfaces are extremely hot!
ALWAYS allow sufficient time for
both surfaces to
cool down before
touching.
To avoid injury, you MUS T read
and understand operator's manual
before using this machine.
This machine to be operated by
qualified personnel only.
Ask for training as needed.
Once lamp is turned OFF , Allow
lamp to cool down before turning
back on. It will take about 5
minutes before lamp can be
turned back on.
ALWAYS disconnect the GloBug
Solo Jr.'s AC power cable from
generator first, before shutting
down generator.
ALWAYS turn on generator first,
before connecting the GloBug
Solo Jr.'s AC power cable to
generator.
TRIPOD DEPLOYMENT
SET
1 Undo the band and pull tripod
downward at the tip end.
2 Lift up the mast to hook the latch.
RELEASE
1 Lift up the mast and pull the band
upward to unhook the latch.
2 Hold the mast and pull the band
upward until the tripod place in stow
position.
DANGER
Make sure the power cable
from the generator is
connected to the lamp
power cable securely.
A loose connection may
cause a short circuit.
NEVER use without hooking
the latch. The possibility exists
of tipping.
BAND
LATCH
Upper
position
Lower
position
DCL1260
DCL1262
2
2
3
4
5
6
1
NAMEPLATE AND DECALS.
Go
to
Discount-Equipment.com
to
order
your
parts