![background image](http://html1.mh-extra.com/html/multiquip/globug-gb12bp/globug-gb12bp_operation-and-parts-manual_1855133021.webp)
GLOBUG LIGHTING SYSTEM — OPERATION AND PARTS MANUAL — REV. #2 (11/03/08) — PAGE 21
GLOBUG GB12BW/BS/BP LIGHTING SYSTEM — SETUP (GB12BS)
The pole clamp assembly used
in this setup procedure is a dual
type clamp. One side of the
clamp is for the attachment of
the main pole of the lighting
system. The other side of the
clamp is used for the
attachment of a support pole that is usually connected to a
piece of equipment such as a paver.
NOTE
T-HANDLE
LAMP
ASSEMBLY
OFFSET
POLE
ADJUSTABLE
EXTENSION
POLE
EQUIPMENT
SUPPORT
POLE
MAIN POLE
CLAMP
ADJUSTABLE
CHANNEL
ADJUSTMENT
BOLT AND
LOCKNUT
MAIN
POLE
7.0 IN.
(140 MM)
3.0 IN.
(76.2 MM)
EXTENSION
CLAMP
BOLT
REMOVE
WRENCH
C
WINGNUT
E
G
POLE
CLAMP
ASSY.
LOCKNUT
EQUIPMENT
SUPPORT
POLE CLAMP
M
OFFSET
ADAPTER
CLAMP
O
LAMP
POWER
CABLE
P
B
D
L
F
POLE
CLAMP
ASSEMBLY
TENSION
PLATE
H
I
J
K
N
Q
A
POLE
CLAMP
ASSY.
Figure 26. Offset Pole Assembly
Pole Setup (GB12BS)
Refer to Figure 26 for the following procedure.
1. Remove the offset pole
(B)
from the shipping container.
2
Attached to the offset pole is a 17/19 mm open-end
wrench
(C)
. Remove the wingnut
(D)
securing the wrench
to the offset pole and remove wrench.
3. Reinsert wingnut and washer back into offset pole so
they will not get lost or misplaced.
4. Remove the two pole clamp assemblies
(A)
from the
shipping container.
Attach one pole clamp assembly
(E)
to the main pole
(F)
about 3 inches (76.2 mm) down
from the main pole extension clamp. Using supplied 19
mm wrench, tighten locknut on the pole clamp assembly
securely.
5. Attach the other pole clamp assembly
(G)
to the main
pole
(F)
about 7.0 in. (140 mm.) down from the previous
attached pole clamp assembly
(E)
. Using the 19 mm
wrench, tighten locknut on the pole clamp assembly
securely.
6. To attach main pole
(F)
to equipment support pole
(I)
,
swing open adjustable tension plate
(H)
on clamp so
that it can accomodate the diameter of the equipment
support pole. Insert equipment support pole
(I)
through
the two equipment support pole clamp assemblies as
shown in Figure 26.
7. Once the equipment support pole
(I)
has been seated
properly, move adjustment bolt and locknut
(J)
into
locking position. Use the supplied 17 mm wrench, to
tighten locknuts
(J)
on both clamps securely.
8. Place offset pole
(B)
with adapter clamp
(K)
on top of
adjustable extension pole
(L)
. Make sure that offset pole
has been seated correctly.
9. Using 17 mm wrench, tighten both bolts
(M)
on the offset
adapter clamp
(K)
securely.
10. Place lamp assembly
(N)
onto offset pole
(B)
. Tighten T-
handle bolt
(O)
securely.
Go
to
Discount-Equipment.com
to
order
your
parts