manualshive.com logo in svg

Multiple Awnings Multiple Shade, User And Installation Manual

Share
Download
Multiple Awnings Multiple Shade User And Installation Manual Download Page 3

Multiple Awnings inc. – 1505A rue de l’Industrie, Beloeil QC, J3G 0S5 CANADA  

 

3 

Multiple Shade EN V01.3 04  2019 

2. READ ME! 

This  section  contains  IMPORTANT  WARNINGS  concerning  YOUR  SAFETY  and  the 
INTEGRITY OF YOUR MULTIPLE SHADE AND INSTALLATION. 
IMPORTANT SAFETY NOTICE: IT IS MANDATORY TO FOLLOW ALL INSTALLATION 
INSTRUCTIONS, FAILURE TO DO SO MAY RESULT IN BODILY INJURIES, MATERIAL 
DAMAGE AND VOID THE WARRANTY.  
NOTE:  BEFORE  INSTALLING  YOUR  MULTIPLE  SHADE,  CHECK  YOUR  INSTALLATION 
SURFACE TO IDENTIFY ANY POTENTIAL OBSTRUCTIONS THAT COULD INTERFERE WITH 
THE SOLAR SHADE DURING OPENING SUCH AS FIXTURES, DOOR HANDLES ETC.  
WARNING: Your Multiple Shade is not made to support high winds and accumulation of 
snow or ice. This can severely damage your Multiple Shade or make it fall and cause 
corporal and material damage and subsequently void the warranty.  

3. Getting ready 
3.1. Tools and help you will need 

 

Security knife for unpacking      

 

 

2 ladders or step ladders 

 

Chalk line 

 

Measuring tape 

 

Pencil (Ink marker or carpenter’s pencil) 

 

Ratchet and Socket (5/16’’) 

 

Philips screwdriver to open the tube 

 

3 mm, 4 mm and 5 mm Allen key 

 

Drill 

 

Level 

To install in wooden structures: 3/32’’ bit 
To install in masonry structures: 3/16’’ Masonry bit 
Optional: 

 

Stud finder 

 

Masking tape 

 

Caulking 

You will need help to perform the installation. It takes two persons to safely install a 
Multiple Shade. 

Summary of Contents for Multiple Shade



























Reviews:

No comments

Brands by name

Popular brands

Load more brands