Multilink 010-505-10 Installation And Operation Manual Download Page 15

Page: 15 / 18

•

Multilink Inc.

580 Ternes Ln. | Elyria,OH 44035 | 440.366.6966 | www.gomultilink.com

Safety Automatic Transfer Switch Shutdown

Section 6: Safety Automatic Transfer Switch Shutdown

If SATS shutdown becomes necessary at any time, observe the following procedure:

1. Operate the upstream AC utility input circuit breaker servicing the enclosure to the OFF position.

2. Operate the UPS’ DC and AC breakers to the OFF position and disconnect the battery harness.

3. Operate the UPS Input circuit breaker on the SATS to the OFF position.

4. If a generator is in use, disconnect the generator from the outside cabinet generator connector.

Replacement Parts

Section 7: Replacement Parts

If parts become damaged or lost during operation, replacement parts are available from Multilink.

535-037-10:

7-position terminal block plug.

540-020-10:

2-position jumper .025sq post for JMP-P, JMP-G, and JMP-M.

870-242-20:

Power harness for EDP series UPS.

870-252-20:

Power harness for Universal/Line Interactive UPS.

Fuses:

F1: 1/2 Amp, Fast-Blow, Cartridge Style, 5mm x 20mm.

F2, F3, F4: 2 Amp, Fast-Blow, Cartridge Style, 5mm x 20mm.

F5, F6, F7: 1 Amp, Slow-Blow, Cartridge Style, 5mm x 20mm.

F8: 6 Amp, Fast-Blow Cartridge Style, 5mm x 20mm.

Summary of Contents for 010-505-10



















Search results

Summary of Contents for 010-505-10

Reviews:

Related manuals for 010-505-10

Brands by name

Popular brands

Multilink 010-505-10, Installation And Operation Manual

Search results

Summary of Contents for 010-505-10

Reviews:

Related manuals for 010-505-10

Brands by name

Popular brands