5
NOTE:
- Pr or - key when running
in MANUAL FLUSH mode will modify
FLUSH TIME for that station.
- Pressing the button when a
station is running in manual
watering will stop flush on the
current station and advance to the
next station.
- Pressing the button when a
station is running In manual
watering will stop the flush on the
current station and revert to the
previous station.
Turn System Off
To turn off controller, press
RETURN/ENTER
key button
until icon resembling water
spray and
OFF
is displayed on
screen. To return controller to
auto programming mode, press
RETURN/ENTER
key. The controller
will immediately return to auto
programming mode and will display
time and battery life indicator.
NODE Quick Check
This circuit diagnostic procedure
can quickly identify "shorts"
commonly caused by faulty
solenoids or when bare common
wire touches a bare station control
wire. To initiate
NODE
Quick Check
procedure:
1.
From Idle Mode, press and hold
+, -, LEFT ARROW, and RIGHT
ARROW
keys.
2.
Display will show all segments.
Release keys.
3.
Press + key to initiate
NODE
Quick Check
test.
4.
Controller will then activate
flushing unit for 1 second to verify
operation.
Battery Life Indicator
Remaining battery life can be
estimated from the battery life
indicator shown on display. The
NODE can operate using either a
Setting Flushing Days
1.
Press
RETURN/ENTER
key until
CALENDAR
icon is displayed. The
program letter (A, B, or C) will be
displayed. Arrows point at specific
days of week in which flushing will
occur.
2.
Press
LEFT
or
RIGHT ARROW
to
scroll though days.
3.
Press
+
key to activate that day
for program displayed, or
-
key to
cancel watering for that day. The
arrow will show on flushing days for
active program.
4.
Press
PRG
key to set days to
flush for a different program, if
desired.
5.
Press
RETURN/ENTER
key
to proceed to next programming
function, or allow controller to
return to Idle mode.
Manual Flushing
Manual flushing allows user to test
the Hydro-Guard® unit or a program
for a specified run time.
Make sure controller is in Idle
Mode.
1.
Press and hold
RIGHT ARROW
until
HAND
icon is displayed. The
station number (always #1) will
be displayed in lower left side of
display along with
RUN TIME
.
2.
Use the
LEFT
or
RIGHT ARROW
to select #1 station if not already
displayed, and
+
or
-
key to set
manual flushing time.
3.
To manually activate a program,
press
PRG
key. Program letter (A,
B, or C) will show on screen. If a
different program is needed, press
PRG
key until desired program is
displayed.
4.
To stop
MANUAL FLUSHING
cycle press - key until time is
reduced to zero.
5.
Press
RETURN/ENTER
key
to proceed to next programming
function, or allow controller to return
to idle mode.
single 9-volt battery or using two
9-volt batteries. Using two 9-volt
batteries will yield approximately
twice the battery life of a single
9-volt battery. The battery life
indicator chart below shows an
estimate of remaining battery life.
Full:
100-60% remaining battery
life
Med:
60-25% remaining battery life
Low:
25-0% remaining battery life
Replace battery immediately!
Resetting Controller
Resetting controller will erase
current program data and restart
controller. A reset does not,
however, delete a program saved to
permanent memory using the Easy
Retrieve Memory feature to save a
preferred program.
1.
From Idle Mode, press and hold
-,
RIGHT ARROW
, and
PRG
keys.
2.
After two seconds screen will go
blank. Continue to hold keys.
3.
12:00 will flash on display.
Release keys.
4.
The controller may show a
countdown from 10 to 1 on
display, and then 12:00 am will
be shown flashing when reset is
complete. The controller can now
be reprogrammed.
Programming Unit
200 SERIES WARM CLIMATE HIGH-PROFILE DIRECT DISCHARGE UNIT
