4
Programming Unit
Programming
The NODE has the capability to
hold 3 programs (A, B, C) and 4
start times per program. When
programming, flashing portion of
display can be changed by pressing
+
or
-
keys. To change something
not flashing, press
LEFT
or
RIGHT
ARROWS
until desired item is
flashing.
Setting Date/Time
1.
Press
RETURN/ENTER
key until
CLOCK
icon is displayed.
2.
All 4 digits will be displayed
representing the year. Use
+
or
-
keys to change year. Press
RIGHT
ARROW
key to proceed to setting
month.
3.
All 4 digits will be displayed
with two digits on left flashing
representing the MONTH. Use
+
or
-
key to change month. Press
RIGHT ARROW
key to proceed lo
setting
DAY
.
4.
Only two digits on right will
be flashing, representing the
DAY
. Press
+
or
-
key to change
day. Press
RIGHT ARROW
key to
proceed to changing
TIME
.
5.
The
AM/PM/24
time setting
is shown flashing. Press
+
or
-
key
to change to AM, PM, or 24:hour
time. Press
RIGHT ARROW
key to
proceed to setting the
HOUR
.
6.
All 4 numbers are shown with
two numbers on the left flashing,
representing the
HOUR
. Press
+
or
-
key to change the hour. Press
RIGHT ARROW
key to proceed to
setting
MINUTES
.
7.
All 4 numbers are shown with
two numbers on right flashing,
representing
MINUTES
. Press
+
or
-
key to change minutes.
(Pressing
RIGHT ARROW
key will
return to
YEAR
setting at step #2.)
8.
Press
RETURN/ENTER
key
to proceed to next programming
function, or allow controller to return
to idle mode.
200 Series Warm Climate Built-In:
(Integrated)
NODE Programming Instructions
Batteries
The NODE uses standard 9-volt
alkaline batteries to operate the
control valve and program the
controller. The controller can
operate with one or two batteries
installed. Under normal conditions,
potential life is 1 year for a single
battery.
Battery Installation
1.
Unscrew rear body of the
NODE to gain access to battery
compartment.
2.
Insert battery/batteries into
battery tray and connect the battery
connector to controller.
3.
Make sure no water is inside
battery compartment.
4.
Screw the NODE rear body back
onto front half.
NOTE: Make sure that seal marker
on rear half of the NODE lines
up with front half, ensuring a proper
seal is created. Also, The NODE has
non-volatile memory, which allows
battery replacement without losing
program information.
Idle Mode - Waking Up
Normally the NODE display shows
time and day, day of week, and
battery life Indicator. During a short
period of inactivity the display will
shut off to retain battery power
Pressing any key will wake up the
NODE to the Idle Mode.
Run Mode
When controller is operating a
program, items shown on display
will include station number (always
"1"), program letter (A, B, or C),
remaining runtime, and a blinking
Rotor icon.
Setting Flush Sequence Start
Times
1.
Press
RETURN/ENTER
key until
CLOCK
icon is displayed.
2.
The
START TIME
will be
displayed flashing, along with the
program letter (A, B, or C) and start
time number (1, 2, 3, or 4) in the
upper left of the display. Up to 4
different start times can be set for
each program.
3.
Use
+
or
-
key to change
START
TIME
for program displayed. Each
press of key will change start time
in 15-minute increments.
4.
Press
RIGHT ARROW
key to
add an additional
START TIME
to
program displayed. The start time
number Is shown in upper left
corner of display.
5.
Press
PRG
key to add
START
TIME
to a different program.
6.
Press
RETURN/ENTER
key
to proceed to next programming
function, or allow controller to
return to Idle mode.
Setting Flush Duration Times
1.
Press
RETURN/ENTER
key until
HOURGLASS
icon is displayed.
RUN
TIME
will be displayed flashing.
Also shown is program letter (A, B,
or C) and active station# (always
#1- all other stations not used) on
lower left side of display.
2.
Press
+
or
-
key to change
station
RUN TIME
from 1 minute
to 6 hours.
3.
Press
PRG
key to add a
RUN
TIME
to another program.
4.
Press
RETURN/ENTER
key
to proceed to next programming
function, or allow controller to
return to Idle mode.
200 SERIES WARM CLIMATE HIGH-PROFILE DIRECT DISCHARGE UNIT
