Mueller SENTRY II Installation And Operation Manual Download Page 82

Page: 82 / 83

Sentry II Service Reference Form, Programmable Features

Please detach, complete, and leave in Sentry II control box for future reference.

Mueller Authorized Dealer:

End User/Owner:

Name:

Address:

Phone:

Contact:

Please check the selected program options:

Description:

Options and Selection

Bottom Unit(s) Cooling Delay

0-120 minutes

________ minutes

All Units Cooling Delay

0-120 minutes

________ minutes

Pre-Start Cooling

______ 30 minutes

______ 60 minutes

Pre-Start Agitation

______ 30 minutes

______ 60 minutes

Interval Agitation

______ 3 out of 18 min. ______ 3 out of 30 min.

Sample Agitation

______ 2 minutes

______ 5 minutes

______ 10 minutes

Pre-Rinse Temperature

______ Cold

______ Warm

Fifth-Cycle for Complete Wash ______ On

______ Off

______ n/a Japan Program

Fifth-Cycle (Acid or Sanitize)

______ Acid

______ Sanitize

______ n/a Japan Program

Acid/Sanitize Temperature*

______ Cold

______ Warm

Delayed Start - Complete Wash ______ None

______ 45 minutes

*Selects sanitize temperature only with Japan program.

Sentry Information:

Milk Cooler Information:

Part Number/Model:

Serial Number:

Comments:

Sentry II Operating Instructions

Effective April 1, 2000

Summary of Contents for SENTRY II




















































































Search results

Summary of Contents for SENTRY II

Reviews:

Mueller SENTRY II, Installation And Operation Manual, Page: 82 / 83

Search results

Summary of Contents for SENTRY II

Reviews: