MTU 12V2000B26F Operating Instructions Manual Download Page 22

Inclined positions, standard oil system (reference: waterline)

Number of cylinders

12

16

18

Longitudinal inclination, continu-
ous max. driving end bottom (op-
tion: max. operating inclination po-
sitions)

L

Degrees (°)

5

5

5

Longitudinal inclination, continu-
ous max. driving end top (option:
max. operating inclination posi-
tions)

L

Degrees (°)

5

5

5

Transverse inclination continuous
max. (design: max. operating incli-
nation positions)

L

Degrees (°)

10

10

10

Table 14: Inclined positions, standard oil system (reference: waterline)

Capacities

Number of cylinders

12

16

18

Engine coolant capacity, engine
side (without cooling system)

R

Liters

63

70

73

Charge-air coolant, engine side

R

Liters

-

-

-

Fuel, engine side

R

Liters

6

6

7

Engine oil capacity, initial filling
(standard oil system) (design: max.
operating inclination positions)

R

Liters

92

114

122

Oil change quantity max. (standard
oil system) (design: max. operating
inclination positions)

R

Liters

80

102

110

Table 15: Capacities

Fan / fan cooler

Number of cylinders

12

16

18

Fan, push-type

X

X

X

Fan drive: mechanical via V-belt

X

X

X

Table 16: Fan / fan cooler

Sound

Number of cylinders

12

16

18

Exhaust noise, not attenuated - DL
(free-field sound pressure level Lp,
1 m distance, ISO 6798, +3 dB(A)
tolerance)

R

dB(A)

111

-

-

Exhaust noise, not attenuated - DL
(sound power level LW, ISO 6798,
+3 dB(A) tolerance)

R

dB(A)

124

-

-

22 | Technical Data | MS150118/00E 2014-07

TIM-ID: 0000053440 - 001

Summary of Contents for 12V2000B26F




















































































































































Reviews: