background image

582 – AL Emergency Stop Failure

ZKP-Number: 1.1005.006

Emergency stop command was not executed
Flashing pre-alarm and alarm

Cause

Corrective action

Engine speed does not come to

a standstill within a configurable

period.

u

Contact Service.

584 – AL CAN Start clearance failed

Yellow alarm; warning

Cause

Corrective action

Yellow alarm; warning; CAN

object Start clearance was not

received within the expected

time period.

u

Contact Service.

586 – LO P-Oil Refill Pump

ZKP-Number: 2.0159.911

Oil pressure in refill pump is too low - limit value 1
Yellow alarm; warning

Cause

Corrective action

Oil level in oil refill tank too low.

1. Check oil level, top up as necessary (→ Page 211).

2. Contact Service.

588 – SD P-Oil Refill Pump

ZKP-Number: 1.0159.910

Signal error, refill pump oil pressure sensor
Yellow alarm; warning

Cause

Corrective action

Pressure sensor defective.

Short circuit or wire break.

1. Check sensor and wiring, replace as necessary (→ Page 248).

2. Contact Service.

593 – AL T-Lube Oil in Oil Pan too Low

ZKP-Number: 2.1090.929

Lube oil temperature in oil pan is too low.

Cause

Corrective action

Preheating time is insufficient.

1. Extend preheating period.

2. Contact Service.

MS150110/00E 2013-10 | Troubleshooting | 163

TIM-ID: 0000045495 - 001

Summary of Contents for 12 V 4000 Mx4
















































































































































































































































































Reviews: