MTI RAPIDDOC LITE Installation Manual Download Page 10

Page: 10 / 12

RAPIDDOC

™

LITE INSTALLATION GUIDE

www.MTIGS.com | T:800.426.6844

LED Status

Case Docked

Case Removed

Case Ready for Removal

12V Tablet Warning

RapicdDoc Lite only

supports 5V Apple

Tablets. If you place a

12V Tablet on a Lite

base, the LED will start

flashing and the latches

will click 10 times.

Remove the Tablet or

it will be locked for 2

minutes.

Manual Release

Use the other hand to remove the case while keeping the
security screw turned.

Insert the Red Handle Tool into the security screw hole at
the bottom of the RapidDoc base-disk under the tablet.
Turn the Red Handle Tool clockwise until resistance is
felt (about halfway) and hold.

Do not grab the tablet until after

you twist the Red Handle Tool, the

magnets in the case will keep the

tablet securely in place.

-CONTROLLED DOCUMENT-

063-00223

C-0

Status: Approved

ECO-111786

Summary of Contents for RAPIDDOC LITE













Search results

Summary of Contents for RAPIDDOC LITE

Reviews:

Related manuals for RAPIDDOC LITE

Brands by name

Popular brands

MTI RAPIDDOC LITE, Installation Manual

Search results

Summary of Contents for RAPIDDOC LITE

Reviews:

Related manuals for RAPIDDOC LITE

Brands by name

Popular brands