MTHTrains 20-20304-1 Operator'S Manual Download Page 18 | Manualshive

Page: 18 / 50

background image

Master Volume

F6 – Master Volume

There are 10 volume levels. Pressing F6 twice (toggling on then off) raises the Master
Volume one level. The Master Volume loops. That is, if you go past the 10th level it will
loop back around to the 1st or lowest volume level.

Couplers

Your MTH PS3.0-equipped engine comes with remotely controlled Proto-Couplers.
They can be fired using your DCC handheld.

F7 – Front Coupler

Pressing F7 twice (toggling on then off) will fire your Front Coupler

F8 – Rear Coupler

Pressing F8 twice (toggling on then off) will fire your Rear Coupler

Forward/Reverse Signal

Just like a real engine, you can announce the direction of intended movement using your
DCC handheld and F9 and F10.

F9 – Forward Signal

Pressing F9 twice (toggling on then off) will sound the Forward Signal. This is two
whistle/horn blasts

F10 – Reverse Signal

Pressing F10 twice (toggling on then off) will sound the Reverse Signal. This is three
whistle/horn blasts

Grade Crossing Signal

Again, just like a real engine, you can trigger the Grade Crossing Signal on your engine.
This is two long, one short, one long whistle/horn blast.

F11 – Grade Crossing Signal

Pressing F11 twice (toggling on then off) will sound your Crossing Signal.

Smoke (if Equipped)

F12 – Smoke On/Off

Enabling F12 will turn the smoke unit on. Disabling F12 will turn your smoke unit off.

F13 – Smoke Volume

There are three smoke volume levels in your MTH PS3.0-equipped engine –
Low/Med/High. The default for this is set to High. You can adjust the smoke output
(amount of smoke the generator puts out) by pressing the F13 button twice. This sets the
level to the next step. For example, if you are currently at the High smoke output level,
pressing F13 twice (toggling it on then off) will set the smoke volume to Low. Pressing F13
twice again will set it to Medium and so on.

Premier

ABA Diesel Engine w/ Proto-Sound® 3.0

18

Alco FA-2

«
...
16
17
18
19
20
...
»

Summary of Contents for 20-20304-1



















































Reviews:

No comments

Related manuals for 20-20304-1

Brand: Radio Shack Pages: 8

Brand: Old School Model Works Pages: 14

Brand: LAEGENDARY Pages: 32

Brand: Skippy Buddy Pages: 2

Brand: Trix Pages: 20

Brand: Matchbox Pages: 2

Star Wars 75060

Brand: LEGO Pages: 307

Boulton Paul Defiant Mk I

Brand: WarbirdKits Pages: 17

Jumpin' Jackpot

Brand: NAMCO Pages: 12

Brand: THINK GIZMOS Pages: 30

Brand: STUDIO27 Pages: 4

N-Strike Mega Bulldog

Brand: Nerf Pages: 2

Touch & Swipe Baby Phone - Pink

Brand: VTech Pages: 12

Sopwith camel 3451

Brand: LEGO Pages: 52

Brand: TTS Pages: 4

Brand: myToys Pages: 6

Brand: GRAUPNER Pages: 7

My First Learning Tablet

Brand: LeapFrog Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands