MTHTrains 20-20304-1 Operator'S Manual Download | Manualshive

Page: 11 / 50

background image

Your engine is equipped with a sound package of either passenger station announce-
ments or freight yard sounds that you can play when you pull into a station or a yard.

Each sequence described below will play as long as it is left on, randomly generating
sounds, but be sure to allow approximately 30 seconds between the button pushes

described below to allow the PFA sufficient time to run through each sequence.

•To cue the sound system to play the PFA, quickly but firmly tap the Bell

button once followed by 2 quick taps of the Horn button while the

engine is moving. Tap the buttons quickly but allow approximately

½ second between each press.

• Press the Direction button once to stop the engine. This will trigger the

first sequence of PFA. The reverse unit is temporarily disabled so that the

train will not move as you use the Direction button to trigger the sounds.

Proto-Sound 3.0 has disabled operator control over the Horn and Bell
buttons until the full PFA sequence is complete.

•After waiting about 30 seconds for that sequence to run, press the

Direction button again to trigger the second sequence of PFA.

•After about 30 seconds, press the Direction button again to trigger the

third PFA sequence.

•Again, after allowing about 30 seconds for that sequence to run, press the

Direction button one more time to trigger the fourth and final PFA

sequence. The PFA will continue and within a few seconds the bell will

begin ringing, then the engine will begin moving at the current throttle

setting, in the same direction it was traveling when you began the sequence.

Once the bell turns off, the operator regains control of the transformer's bell

and Horn buttons and can ring the bell or blow the Horn as usual.

Passenger/Freight Announcements (PFA)

Premier

ABA Diesel Engine w/ Proto-Sound® 3.0

11

Alco FA-2

«
...
9
10
11
12
13
...
»

Summary of Contents for 20-20304-1



















































Reviews:

No comments

Related manuals for 20-20304-1

Brand: J-Power Pages: 32

IDF Merkava Mk.IV

Brand: Eduard Pages: 6

Paradise AquaCraft

Brand: Hobbico Pages: 12

Brand: Eduard Pages: 3

Brand: LAheli Pages: 14

Brand: marklin Pages: 32

INFINITE JOURNEY

Brand: K'Nex Pages: 32

Saab J-35J Draken

Brand: REVELL Pages: 11

Brand: Wrebbit Pages: 40

PREMIER E8 ABA DIESEL ENGINE

Brand: M.T.H. Pages: 24

Monkey Chase H8128

Brand: Fisher-Price Pages: 4

Brand: J. Perkins Pages: 12

USRA 0-8-0 Steam Locomotive and Tender

Brand: Lionel Pages: 36

CHEF CAKE POPS FACTORY

Brand: Smoby Pages: 8

Imagine Build Play MULTI-MOTOR 13074

Brand: K'Nex Pages: 72

Brand: Fisher-Price Pages: 28

35cc EXTRA 300 ARF-QB

Brand: AeroWorks Pages: 80

Brand: Fisher-Price Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands