MTHTrains 20-20304-1 Operator'S Manual Download | Manualshive

Page: 35 / 50

background image

It is recommended to lubricate the outside truck block idler and drive gears with
grease. Use the diagram shown below as a guide and add grease to the points marked.

Figure 11: Greasing the Idler Gears

Cleaning The Wheels, Tires, and

Track

Periodically check the locomotive wheels and
pickups for dirt and buildup, which can cause poor
electrical contact and traction and prematurely wear
out the neoprene traction tires. Wheels and tires can
be cleaned using denatured (not rubbing) alcohol
applied with a cotton swab.

To clean the track, use RailKing Track Cleaning Fluid
found in Maintenance Kit (30-50051) or denatured
(not rubbing) alcohol and a clean rag. Unplug the
transformer and wipe the rails of the track, turning the
rag frequently to ensure that you are using clean cloth
on the rails. Thereafter, keep an eye on the track and
clean it when it gets dirty to ensure good electrical
contact and to lengthen the life of the tires.

Track Cleaning

Block (40-1099)

Maintenance Kit (30-50051)

Premier

ABA Diesel Engine w/ Proto-Sound® 3.0

35

Alco FA-2

Grease Idler Gear (G)

«
...
33
34
35
36
37
...
»

Summary of Contents for 20-20304-1



















































Reviews:

No comments

Related manuals for 20-20304-1

Brand: INTERACTIVE TOY CONCEPTS Pages: 2

Brand: roco Pages: 8

Sea King Mk. 41 45 years SAR

Brand: REVELL Pages: 16

Brand: LEGO Pages: 84

LITTLEPEOPLE N0716

Brand: Fisher-Price Pages: 4

Brand: Faller Pages: 12

P-39 Q/N AIRACOBRA

Brand: VQ Radio Control Model Pages: 12

Brand: Radica Games Pages: 2

Brand: GREAT PLANES Pages: 20

Brand: Kavan Pages: 16

CHEF CAKE POPS FACTORY

Brand: Smoby Pages: 8

Radio Control Pterodactyl

Brand: Toysrus Pages: 2

Smokescreen 7051

Brand: Hasbro Pages: 16

Zoom F/A-18C Hornet S.A.

Brand: Eduard Pages: 3

Brand: Step2 Pages: 11

Travel Air BH.06

Brand: Black Horse Model Pages: 23

Brand: Badger Basket Pages: 6

SERVICING AREA ACCESSORIES

Brand: Faller Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands