MTD Yard Machines LT31S Operator'S Manual Download | Manualshive

Page: 5 / 20

background image

5

SAFETY AND INTERNATIONAL SYMBOLS

This operator's manual describes safety and international symbols and pictographs that may appear on this product.
Read the operator's manual for complete safety, assembly, operating and maintenance and repair information.

RULES FOR SAFE OPERATION

SYMBOL

MEANING

• SAFETY ALERT SYMBOL

Indicates danger, warning, or
caution. May be used in conjunction
with other symbols or pictographs.

• WARNING - READ OPERATOR'S

MANUAL

Read the Operator’s Manual(s) and
follow all warnings and safety
instructions. Failure to do so can
result in serious injury to the
operator and/or bystanders.

• WEAR EYE AND HEARING

PROTECTION

WARNING:

Thrown

objects and loud noise can cause
severe eye injury and hearing loss.
Wear eye protection meeting ANSI
Z87.1-1989 standards and ear
protection when
operating this unit. Use a full face
shield when needed.

• KEEP BYSTANDERS AWAY

WARNING:

Keep all

bystanders, especially children and
pets, at least 50 feet (15 m.) from the
operating area.

• UNLEADED FUEL

Always use clean, fresh unleaded fuel.

SYMBOL

MEANING

• THROWN OBJECTS AND

ROTATING CUTTER CAN CAUSE
SEVERE INJURY

WARNING:

Do not

operate without the cutting
attachment shield in place. Keep
away from the rotating cutting
attachment.

• ON/OFF STOP CONTROL

ON / START / RUN

• ON/OFF STOP CONTROL

OFF or STOP

• HOT SURFACE WARNING

Do not touch a hot muffler or
cylinder. You may get burned. These
parts get extremely hot from
operation. When turned off they
remain hot for a short time.

• CHOKE CONTROL

1 • FULL choke position
2 • PARTIAL choke position
3 • RUN position

• OIL

Refer to operator's manual for the
proper type of oil.

1

2

3

«
...
3
4
5
6
7
...
»

Summary of Contents for Yard Machines LT31S





















Reviews:

No comments

Related manuals for Yard Machines LT31S

Brand: Nakayama Pages: 34

Brand: Dolmar Pages: 68

Brand: Oleo-Mac Pages: 76

Brand: Yard-Man Pages: 104

Brand: BaByliss for MEN Pages: 56

Brand: Parkside Pages: 66

Brand: Parkside Pages: 70

Brand: WARRIOR Pages: 31

Brand: Leviton Pages: 3

Decora Smart D26HD

Brand: Leviton Pages: 19

Brand: Ruris Pages: 69

Brand: Wahl Pages: 2

Brand: McCulloch Pages: 12

Brand: Ryobi Pages: 14

Brand: Ryobi Pages: 34

Brand: FIBARO Pages: 36

Brand: Yard-Man Pages: 82

Brand: Oregon Scientific Pages: 92

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands