background image

2

TABLE OF CONTENTS

FINDING MODEL NUMBER

This Operator’s Manual is an important part of your new snow thrower. It will help you assemble, prepare 
and maintain the unit for best performance. Please read and understand what it says. 

Before you start assembling your new equipment

, please locate the model plate on the 

equipment and copy the information from it in the space provided below. A sample model plate is 
also given below. You can locate the model plate by standing at the operating position and 
looking down at the rear of the snow thrower. This information will be necessary to use the
manufacturer’s web site and/or help from the Customer Support Department or an authorized 
service dealer. 

CUSTOMER SUPPORT

Please do NOT return the unit to the retailer from where it was purchased, without first contacting Customer Support.

If you have difficulty assembling this product or have any questions regarding the controls, operation or 
maintenance of this unit, you can seek help from the experts. Choose from the options below:

Visit 

mtdproducts.com

 for many useful suggestions. Click on Customer Support button and 

you will get the four options reproduced here. Click on the appropriate button and help is 
immediately available. 

If you prefer to reach a Customer Support Representative, please call 

1-800-800-7310

The 

engine

 manufacturer is responsible for all engine-related issues with regards to 

performance, power-rating, specifications, warranty and service. Please refer to the engine 
manufacturer’s Owner’s/Operator’s Manual, packed separately with your unit, for more 
information.

Content

Page

Important Safe Operation Practices

3

Assembling Your Snow Thrower

5

Know Your Snow Thrower

7

Operating Your Snow Thrower

8

Making Adjustments

10

Maintaining Your Snow Thrower

11

Servicing Your Snow Thrower

12

Trouble Shooting

14

Illustrated Parts

15

Warranty

20

Content

Page

Copy the model number here:

Copy the serial number here:

www.mtdproducts.com

MTD  LLC
P. O. BOX  361131
CLEVELAND,OH 44136
330-220-4683
800-800-7310

The answer you are
looking for could be just
a mouse click away!

The answer you are
looking for could be just
a mouse click away!

Engine

Manual

Summary of Contents for 3BA





















Reviews: