background image

5

SECTION 2:  ASSEMBLING YOUR SNOW THROWER

IMPORTANT: 

This unit is shipped with the engine full of 

oil. After assembly, see page 8 for fuel and oil details. 

Removing From Carton 

Cut the corners of the carton and lay the sides flat 
on the ground. Remove all packing inserts.

Move the snow thrower out of the carton.

Make certain the carton has been completely 
emptied before discarding it. 

Before Assembly

NOTE: 

Reference to right, left, front or rear of the unit is

from the operating position unless otherwise stated. 

Cut the cable tie that secures the upper handle to 
the chute assembly for shipping purposes.

Setting Up The Handle

Loosen the chute knob on the upper chute and 
pivot the upper chute upwards as far as it will go. 
Follow the direction of the arrow in Figure 1.

Figure 1

Loosen the handle knob, saddle washer and 
handle tab on each side of the handle. See Figure 
2.

Figure 2

Hold both controls against the upper handle and 
pull up as shown in Figure 3. Make sure that the 
upper handle locks over the lower handle and the 
handle tabs align with the handle. You may have to 
carefully maneuver the upper handle to clear the 
chute assembly.

CAUTION: 

Be careful not to bend or kink the cables.

 

Figure 3

Tighten the handle knobs on each side of the 
handle. Refer to Figure 2.

Rotate the chute by the chute handle to the desired 
operating position. 

Tighten the chute knob on the upper chute making 
sure the flat washer and the carriage bolt are 
correctly positioned. Refer to Figure 1.

Clean-Out Tool

This tool and the electric extension cord, if so equipped, 
may be fastened with a cable tie to the rear of the auger 
housing for shipping purposes. In that case, cut the 
cable tie and remove the extension cord now.

WARNING: 

Do not lift the snow thrower by 

the chute handle. 

Chute Handle*

Chute Knob

* Meant only to rotate the chute

Upper Chute

Hex Bolt

Handle Tab

Handle 
Knob

Saddle
Washer

Initial position of 
Upper Handle

Final position of
Upper Handle

Summary of Contents for 3BA





















Reviews: