8
To Start Engine
•
Attach spark plug wire to spark plug. Make certain
the metal loop on end of the spark plug wire (inside
the boot) is fastened securely over the metal tip on
the spark plug.
•
Make certain the auger and drive controls are in the
disengaged (up) position.
•
Move throttle control up to FAST position. Insert
ignition key into slot and snap in place. See Figure
5.
Do not turn key.
NOTE:
Engine will not start unless ignition key is
inserted into ignition slot in carburetor cover.
Electric Starter
•
Determine that your house wiring is a three-wire
grounded system. Ask a licensed electrician if you
are not certain.
•
If your house wiring system is not a three-wire
grounded system, do not use this electric starter
under any conditions.
WARNING: The electric starter is
equipped with a grounded three-wire
power cord and plug and is designed to
operate on 120 volt AC household
current. It must be used with a properly
grounded three-prong receptacle at all
times to avoid the possibility of electric
shock. Follow all instructions carefully
prior to operating the electric starter.
•
If your home electrical system is grounded, but a
three-hole receptacle is not available, one should
be installed by a licensed electrician before using
the electric starter.
•
If you have a grounded three-prong receptacle,
proceed as follows:
•
Move engine speed control to “Fast” position and
set Choke Control to “Full” position.
•
Push Primer three (3) times, making sure to cover
vent hole when pushing.
•
Connect power cord to switch box on engine. Plug
the other end of power cord into a three-hole,
grounded 120 volt AC receptacle.
•
Push starter button on top of the engine to crank
engine. As you crank the engine, move choke knob
to FULL choke position.
•
When engine starts, release starter button, and
move choke gradually to OFF. If engine falters,
move choke immediately to FULL and then
gradually to OFF.
•
When disconnecting the power cord, always unplug
from the three-prong receptacle first and then from
the snow thrower.
Recoil Starter
•
Rotate choke knob to FULL choke position (cold
engine start). If engine is warm, place choke in OFF
position instead of FULL.
•
Push primer button two or three times. If engine is
warm, push primer button once only.
NOTE:
Always cover vent hole in primer button when
pushing. Additional priming may be necessary for first
start if temperature is below 15°F.
•
Grasp starter handle and pull rope out slowly, until
it pulls slightly harder. Let rope rewind slowly.
•
Pull starter handle rapidly. Do not allow handle to
snap back. Allow it to rewind slowly while keeping a
firm hold on the starter handle.
•
Repeat the previous steps until engine starts.
To Stop Engine
•
Run engine for a few minutes before stopping to
help dry off any moisture on the engine.
•
To help prevent possible freeze-up of starter,
proceed as follows:
Electric Starter:
•
Connect power cord to switch box on engine, then
to 120 volt AC receptacle. With the engine running,
push starter button and spin the starter for several
seconds. The unusual sound made by spinning the
starter will not harm engine or starter. Disconnect
the power cord from receptacle first, and then from
switch box.
Recoil Starter
•
With engine running, pull starter rope with a rapid,
continuous full arm stroke three or four times.
Pulling the starter rope will produce a loud clattering
sound, which is not harmful to the engine or starter.
•
To stop engine, move throttle control to “stop” or
“off” position.
•
Remove ignition key (DO NOT turn key) to prevent
unauthorized use of equipment.
NOTE:
Do not lose ignition key. Keep it in a safe place.
Engine will not start without ignition key.
•
Wipe all snow and moisture from the carburetor
cover in the area of the control levers. Also, move
control levers back and forth several times.
To Engage Track Drive
•
With the engine running near top speed, move the
shift lever into one of the six FORWARD positions
or two REVERSE positions. Select a speed
appropriate for the snow conditions that exist.
•
Squeeze the auger control and the augers will turn.
Release it and the augers will stop.
•
Squeeze the drive control and the snow thrower will
move. Release it and drive motion will stop.
•
NEVER move shift lever without releasing drive
control.
Summary of Contents for 31AH7L3G701
Page 17: ...17 NOTES ...
