background image

ManualNightFighterInstallation.doc  

 

Prnt Spec. 10000005389(B)   Mat. 10035581 

07/23/02  

 

Page 1 of 15 

NightFighter™ 

 
 

INSTALLATION INSTRUCTIONS 
 
BRACKET AND TRANSMITTER KIT 

 
 
 

WARNING! 

Read this manual carefully if you have or will have the responsibility for using or servicing 
the product.  The ClearCommand™ Communications System from MSA will perform as 
designed only if used and serviced according to the instructions.  Otherwise, the product 
could fail to perform as designed, and persons who rely on this product could sustain 
serious personal injury or death. 

 
The warranties made by MSA with respect to the product are voided if the product is not used 
according to the instructions in this manual.  We encourage our customers to write or call for a 
demonstration of this equipment prior to use, or for any additional information relative to use or 
repairs.  Call 1-800-MSA-2222 during regular working hours. 
 
NIOSH and NFPA certified as an accessory for the Ultra Elite facepiece for use with the MSA 
MMR, MMR with Slide Connection and BMR breathing apparatus only. 
 
 

This device complies with Part 15 of the FCC Rules. Operation is subject to the following 

conditions: (1) this device may not cause harmful interference, and (2) this device must accept 

any interference that may cause undesired operation. 
 

Changes or modifications not expressly approved by the manufacturer could void the user’s 
authority to operate the equipment.

 

 

 

Summary of Contents for NightFighter
















Reviews: