background image

 Page 2

Safety Precautions

mrcool.com

WARNING

Please read the manual in its entirety before installing, operating or repairing.
DO NOT 

share the electrical circuit with other appliances. Improper or insufficient power 

supply can cause fire and/or electrical shock.

DO NOT

 

allow any substances or gases to enter the unit when connecting refrigerant 

piping. The presence of other gases or substances will lower the unit’s capacity and may 

cause abnormally high pressure in the operation cycle. This could cause an explosion 

and/or personal injury. 

DO NOT 

connect the ground wire to a gas pipe, water pipe, lightning arrester, or telephone 

wire.

 

DO NOT 

allow children to play with the air conditioner. Children should be supervised 

around the unit at all times.

DO NOT 

alter the settings of the pressure sensor or other protective devices; if 

short-circuited or modified, fire and/or an explosion could occur. 

Installation must be performed by an authorized technician. Improper installation may cause 

water leakage, electrical shock, and/or fire. 

Installation must be performed according to installation instructions. Improper installation may 

cause water leakage, electrical shock, and/or fire. 

In North America, installation must be performed in accordance with the requirements of the NEC 

and CEC (by authorized personnel only). Contact an authorized service technician for repair or 

maintenance of the unit.

Only use the included accessories and specified parts for installation. Using non-standard parts 

can cause water leakage, electrical shock, fire, and could cause the unit to fail.
The United States Environmental Protection Agency (”EPA”) has issued various regulations 

regarding the introduction and disposal of refrigerants introduced into this unit. Failure to follow 

these regulations may harm the environment and can lead to a substantial fine. These regulations 

may vary due to the passage of laws. A certified technician must perform the installation and 

service of this product. Should questions arise, contact your local EPA office.

Read Before Installation 

Incorrect installation may cause serious damage or injury.

The seriousness of potential damage or injuries is classified as

 either a 

WARNING 

or 

CAUTION

.

WARNING

CAUTION

This symbol indicates ignoring instructions may cause death or serious injury.

This symbol indicates that ignoring instructions may cause moderate personal

injury, damage to your unit, or other property.

This symbol indicates that you should 

NEVER 

perform the indicated action. 

1.

2.

3.

4.

!

Safety Precautions

5.

Summary of Contents for Universal MDUI180 E Series
































Reviews: