MR VACUTAP Operating Instructions Manual Download Page 18 | Manualshive

Page: 18 / 96

background image

3 Product description

Maschinenfabrik Reinhausen GmbH 2020

18

5788897/03 EN

VACUTAP

®

VVS

®

3.1.3 Nameplate and serial number

The nameplate with serial number is on the on-load tap-changer head cover.

Figure 4: Nameplate

3.1.4 Protective devices

The on-load tap-changer is equipped with the following protective devices.

3.1.4.1 Protective relay

3.1.4.1.1 Function description

The protective relay is looped into the circuit breaker tripping circuit, thus
protecting the on-load tap-changer and transformer in the event of a fault
within the on-load tap-changer oil compartment. It is tripped when the speci-
fied speed of flow from the on-load tap-changer head to the oil conservator
is exceeded due to a fault. The flowing insulating fluid actuates the flap valve
which tips over into position OFF. The contact in the dry-reed magnetic
switch is thereby actuated, the circuit breakers are tripped, and the trans-
former is de-energized.

The protective relay is a component of an on-load tap-changer filled with in-
sulating fluid and its properties conform to the respective applicable version
of IEC publication 60214-1.

Diverter switch operations at rated switching capacity or at permissible over-
load will not cause the protective relay to trip.

The protective relay responds to flow, not to gas accumulated in the protec-
tive relay. It is not necessary to bleed the protective relay when filling the
transformer with insulating fluid. Gas accumulation in the protective relay is
normal.

«
...
16
17
18
19
20
...
»

Summary of Contents for VACUTAP

































































































Reviews:

No comments

Related manuals for VACUTAP

Brand: Makerfire Pages: 10

Brand: NARGESA Pages: 50

Brand: VeEX Pages: 2

Brand: JB-Lighting Pages: 48

Brand: CAIRE Pages: 2

D-MAS HyperSat 2540

Brand: DanMedical Pages: 103

Pro Vantage 12+ Series

Brand: Ecco Pages: 6

AquaPure Ei Series

Brand: Jandy Pages: 4

Brand: janitza Pages: 30

AquaPure Ei Series

Brand: Jandy Pages: 8

Jandy Pro Series

Brand: Jandy Pages: 16

Brand: Laser Pages: 2

Brand: Lars Thrane Pages: 50

Brand: Rain-Flo Irrigation Pages: 16

FlexDraper FD2 Series

Brand: MacDon Pages: 2

OXYGEN PRO MINI

Brand: M-Audio Pages: 56

QNET Physics and Dynamics

Brand: Quanser Pages: 4

Brand: Yamaha Pages: 126

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands