MR VACUTAP Operating Instructions Manual Download Page 59 | Manualshive

Page: 59 / 96

background image

6 Fault elimination

Maschinenfabrik Reinhausen GmbH 2020

59

5788897/03 EN

VACUTAP

®

VVS

®

16. Move the on-load tap-changer head cover over the on-load tap-changer

and align it such that the red triangular marks on the on-load tap-changer
head and on-load tap-changer head cover are in alignment and that the
position of the output shaft on the upper gear unit is aligned with the cor-
responding hollow shaft in the on-load tap-changer head.

Figure 49: Aligning on-load tap-changer head cover

17.

CAUTION!

Risk of crushing. Carefully place the on-load tap-changer

head cover horizontally on the on-load tap-changer head, making sure
that you do not place your fingers between the on-load tap-changer head
and on-load tap-changer head cover. Align the output shaft of the upper
gear unit such that it engages in the corresponding hollow shaft in the
on-load tap-changer head.

Figure 50: Lowering on-load tap-changer head cover

«
...
57
58
59
60
61
...
»

Summary of Contents for VACUTAP

































































































Reviews:

No comments

Related manuals for VACUTAP

Brand: National Instruments Pages: 16

Brand: Jasco Pages: 11

Brand: ParaBody Pages: 3

Brand: Hach Pages: 52

Brand: hager Pages: 2

Brand: Teac Pages: 44

Brand: Te Pari Pages: 6

Brand: Zodiac Pages: 32

DeviceNet CompactPCI 1784-CPCIDS

Brand: Allen-Bradley Pages: 36

Brand: Manley Pages: 18

Brand: Kobelt Pages: 20

Brand: Pottinger Pages: 39

Brand: WAGNER Pages: 20

Fusionchef pearl

Brand: Julabo Pages: 43

Brand: Sagitter Pages: 12

Brand: Invacare Pages: 271

Brand: Godox Pages: 8

Brand: Kärcher Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands