MR VACUTAP Operating Instructions Manual Download Page 63

Page: 63 / 96

7 Maintenance

Maschinenfabrik Reinhausen GmbH 2020

5788897/03 EN

VACUTAP

VVS

7.2 Maintenance intervals

WARNING

Danger of explosion!

If pending maintenance work is not carried out immediately, this may lead to
death or serious injury as a result of a progressive short circuit, for example.

► Adherence to the following maintenance intervals is mandatory.

Interval

Action

After 300,000 switching operations (mo-
tor-drive unit counter reading)

Maintenance of the on-load tap-changer.
Contact the Maschinenfabrik Rein-
hausen GmbH Technical Service [

►

Sec-

tion 6, Page 38] for this.

After 500,000 switching operations (mo-
tor-drive unit counter reading)

Contact the Maschinenfabrik Rein-
hausen GmbH Technical Service [

►

Sec-

tion 6, Page 38].

Table 6: Maintenance plan

A label on the inside of the door of the TAPMOTION® ED motor-drive unit
also specifies the relevant maintenance interval.

Figure 52: Label showing maintenance intervals

Summary of Contents for VACUTAP

































































































Search results

Summary of Contents for VACUTAP

Reviews:

Related manuals for VACUTAP

Brands by name

Popular brands

MR VACUTAP, Operating Instructions Manual

Search results

Summary of Contents for VACUTAP

Reviews:

Related manuals for VACUTAP

Brands by name

Popular brands