MR VACUTAP VMS Operating Instructions Manual Download Page 50

Page: 50 / 80

7 Maintenance

Maschinenfabrik Reinhausen GmbH 2020

5993419/02 EN

VACUTAP

VMS

7.3 Changing the insulation fluid

NOTICE

Damage to the on-load tap-changer!

Small parts in the oil compartment may block the diverter switch insert,
thereby damaging the on-load tap-changer.

► Ensure that parts do not fall into the oil compartment.

► Check that all small parts are accounted for.

Change the insulating fluid in the on-load tap-changer oil compartment and
oil conservator if the dielectric strength and water content are not in compli-
ance with the limit values specified in the technical data.

7.3.1 Moving on-load tap-changer to adjustment position

1. Make a note of the current operating position of the on-load tap-changer.

2. Move the on-load tap-changer to the adjustment position. The adjustment

position is indicated in the on-load tap-changer connection diagram in-
cluded in delivery.

7.3.2 Removing horizontal drive shaft

NOTICE

Damage to the on-load tap-changer and transformer!

Damage to on-load tap-changer and transformer if motor-drive unit is oper-
ated when not coupled!

► Never operate the motor-drive unit if the horizontal drive shaft has been

removed.

► As a precaution, block the motor-drive unit against electrical operation by

actuating the motor protective switch (see operating instructions for "Tap-
motion® ED").

Summary of Contents for VACUTAP VMS

















































































Search results

Summary of Contents for VACUTAP VMS

Reviews:

MR VACUTAP VMS, Operating Instructions Manual, Page: 50 / 80

Search results

Summary of Contents for VACUTAP VMS

Reviews: