MR VACUTAP VMS Page 31 Operating Instructions Manual Download | Manualshive

Page: 31 / 80

background image

4 Commissioning

Maschinenfabrik Reinhausen GmbH 2020

31

5993419/02 EN

VACUTAP

®

VMS

®

4 Commissioning

WARNING

Danger of explosion!

Explosive gases in the oil compartment of the on-load tap-changer, trans-
former, pipework system, oil conservator and at the dehydrating breather
opening can deflagrate or explode and result in severe injury or death!

► Ensure that there are no ignition sources such as naked flame, hot sur-

faces or sparks (e.g. caused by the build-up of static charge) in the trans-
former's immediate surroundings during commissioning and that none oc-
cur.

► Do not operate any electrical devices (e.g. risk of sparks from impact

wrench).

► Only use conductive and grounded hoses, pipes, and pump equipment

that are approved for flammable liquids.

WARNING

Danger of explosion!

Overloading the on-load tap-changer can lead to explosion. Spraying hot in-
sulating fluid and flying parts can lead to death and serious injuries. Prop-
erty damage is highly probable.

► Ensure that the on-load tap-changer is not overloaded.

► Ensure use of the on-load tap-changer in accordance with section "Ap-

propriate use".

► Prevent operations outside of the permitted operating conditions by tak-

ing suitable measures.

4.1 Commissioning transformer at operating site

Before energizing the transformer, check that the motor-drive unit and pro-
tective devices are functioning correctly and fill the on-load tap-changer oil
compartment with fresh insulating fluid.

4.1.1 Filling the oil compartment of the on-load tap-changer with

insulating fluid

NOTICE

Damage to the on-load tap-changer!

Unsuitable insulating fluids cause damage to the on-load tap-changer.

► Only use insulating fluids that meet the requirements in accordance with

IEC 60296.

1.

NOTICE!

Check whether the on-load tap-changer head cover has a

flange for attaching a pressure relief device. If it does, operation without a
pressure relief device is not permitted and may result in damage to the
on-load tap-changer.

ð

Fit a pressure relief device which is approved for this on-load tap-
changer on the on-load tap-changer head.

«
...
29
30
31
32
33
...
»

Summary of Contents for VACUTAP VMS

















































































Reviews:

No comments

Related manuals for VACUTAP VMS

Brand: Panasonic Pages: 180

Brand: OMCA Pages: 36

Brand: Salford Pages: 64

SATURA SPOT LED PRO

Brand: Elation Pages: 41

Brand: Tapco Pages: 16

Brand: Zenbooth Pages: 40

Visium CytAssist

Brand: 10x Genomics Pages: 51

Chromium X Series

Brand: 10x Genomics Pages: 5

Brand: 3M Pages: 48

Brand: 3M Pages: 19

Speedglas G5-01

Brand: 3M Pages: 62

Quickfit Nexus Exit

Brand: Thomas & Betts Pages: 2

Brand: Olsen Pages: 56

Brand: Waterous Pages: 5

Brand: 3TECH Pages: 32

Brand: 4EVAC Pages: 15

Brand: Tate Pages: 7

Brand: Tate Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands