manualshive.com logo in svg

MR VACUTAP VMS, Operating Instructions Manual, Page: 15 / 80

Share
Download
MR VACUTAP VMS Operating Instructions Manual Download Page 15

3 Product description

Maschinenfabrik Reinhausen GmbH 2020

15

5993419/02 EN

VACUTAP

®

 VMS

®

3 Product description

3.1 On-load tap-changer

3.1.1 Function description

On-load tap-changers are used to adjust the transmission ratio of transform-
ers without interrupting the load flow. This makes it possible to compensate
for aspects such as fluctuations in voltage occurring in the power transmis-
sion grid. For this purpose, on-load tap-changers are fitted in transformers
and connected to the active part of the transformer.

A motor-drive unit which receives a control impulse (e.g. from a voltage reg-
ulator) changes the operating position of the on-load tap-changer, as a result
of which the transformer's transmission ratio is adapted to the prevailing op-
erating requirements.

Figure 1: System overview of on-load tap-changer, transformer

1 Transformer tank

6 Upper gear unit

2 Motor-drive unit

7 On-load tap-changer

3 Vertical drive shaft

8 Protective relay

Summary of Contents for VACUTAP VMS

















































































Reviews:

No comments