MR VACUTAP VMS Operating Instructions Manual Download Page 34

Page: 34 / 80

4 Commissioning

Maschinenfabrik Reinhausen GmbH 2020

5993419/02 EN

VACUTAP

VMS

4.1.2.2 Bleeding suction pipe on pipe connection S

1. Remove screw cap from pipe connection S.

Figure 21: Screw cap

NOTICE!

An incompletely bled suction pipe significantly impairs the insu-

lation capability of the on-load tap changer to ground. Open vent screw
and bleed suction pipe completely.

3. Close vent screw.

4. Seal vent screw with screw cap.

4.1.3 Checking motor-drive unit

NOTICE

Damage to the on-load tap-changer / de-energized tap-changer!

Damage to the on-load tap-changer / de-energized tap-changer due to actu-
ation of the on-load tap-changer / de-energized tap-changer without insulat-
ing fluid.

► Ensure that the selector / de-energized tap changer is fully immersed in

insulating fluid and that the oil compartment of the on-load tap-changer is
completely filled with insulating fluid.

Summary of Contents for VACUTAP VMS

















































































Search results

Summary of Contents for VACUTAP VMS

Reviews:

MR VACUTAP VMS, Operating Instructions Manual, Page: 34 / 80

Search results

Summary of Contents for VACUTAP VMS

Reviews: