manualshive.com logo in svg

MQ Multiquip HTX6H, Service Manual

Share
Download
MQ Multiquip HTX6H Service Manual Download Page 24

HTX6H, STX6H TROWEL • SETUP, ADJUSTMENTS AND CALIBRATIONS — REV. #1 (09/07/17) — PAGE 23

MACHINE SETUP AND CALIBRATION

Left Side Trowel Speed Adjustment

1.  Install setup jumper or disable stroke follower.
2.  Start machine, on bare floor and pitch until blade tips 

are about ½” off the ground.

3.  Fully depress pedal and measure Left Side Trowel 

Speed.

4.  Adjust speed limit screw and tighten jam nut (Figure 33).

Figure 33. Left Side Trowel Speed Adjustment

5.  Re-measure speed, repeating steps 2 and 3 until Left 

Side Trowel Speed is correct:

 

160 ± 3 RPM (HTX6H)

 

130 ± 3 RPM (STX6H)

6.  Record L.H. speed on Machine Information and 

Maintenance Log in machine setup area.

Right Side Trowel Speed Adjustment

 

 NOTICE

Stroke sensor must be recalibrated after trowel speed 

adjustment for proper machine operation.

SPEED 

ADJUSTMENT

 NUT

JAM NUT

 NOTICE

Stroke sensor must be recalibrated after trowel speed 

adjustment for proper machine operation.
The trowel speeds should be adjusted on a dry concrete 

floor with the blades pitched slightly (tips about 1/2” off 

ground).

1.  Verify setup jumper is installed or stroke follower is 

disabled.

2.  Fully depress pedal, measure Left Side and Right Side 

Trowel Speed.

3.  Adjust trowel arm connecting rod on the pump actuating 

lever and tighten jam nuts (Figure 34).

Figure 34. Right Side Trowel Speed Adjustment

4.  Re-measure speed and repeat steps 2 and 3 until Left 

Side and Right side are within 1 RPM of each other.

5.  Record R.H. speed on Machine Information and 

Maintenance Log in Machine Setup section.

6.  Remove setup jumper or re-enable stroke follower.

Calibrate Stroke Sensor

1.  Turn machine off for at least 10 seconds.
2.  Restart machine.
3.  Install Setup Jumper or disable Stroke Follower.
4.  Click “Calibration” button on machine setup page.

RIGHT HAND

THREAD 

JAM NUT

CONNECTING

ROD

LEFT HAND

THREAD 

JAM NUT

  CAUTION

Machine movement will occur during this step. Ensure 

machine is secure or operator is present in seat. All 

guards should be in place. Keep fingers, hands, hair, 

and clothing away from all moving parts to prevent injury. 

Summary of Contents for HTX6H

































Reviews:

No comments

Brands by name

Popular brands

Load more brands