background image

mSquad User’s Guide 

17 

 

 
 
 

To summarize the keystrokes:    Assign Worker 

 Device 

 Ping (R) 

 Ping (L) (beeps on 

both to confirm) 

 Worker (R) 

 Worker (L) (scroll L to select worker) 

 Assign (R) 

 

Assign (L) to assign (beeps to confirm) 

 Remove (R) 

 Remove (L) to remove registration or 

Done (R & L) to exit. 

 

5.5 Host ID 

Displays the Head Monitor or mLink ID. For Soldiers, it is its registered Head ID; for a Head, it 
is its registered mLink ID when part of an mPlatoon wireless network. 

5.6 Channel 

Select the operating Channel, from CH1 to CH16.    Ensure that the same selection is made on the 
Head/Host as on all Soldiers in the mSquad.

 

5.7 mPlatoon Wireless Networks   

Future systems will allow multiple (up to 8) mSquads can be connected to form an mPlatoon 
using the mLink-F modem, which communicates up to 2 miles (3 km) with each 
Host/Head(MP400H). The mLink is controlled using the mPower Suite mobile App on a 
smartphone or tablet via Bluetooth within 32 ft (10 m). If an mLink is used, the alarm is also 
transmitted to the command center and displayed on the mobile phone or tablet.    Contact 
mPower for availability. 

 

 

 

 
 
 
 
 
 

Summary of Contents for mSQUAD MP400H






















Reviews: