MPEX MARCY MWB-36780B Owner'S Manual Download | Manualshive

Page: 9 / 15

background image

STEP 4 (See Diagram 4)

A.) Attach the Backrest Supports (#10) onto both ends of the pivot on the Main Seat Support

(#3). Place the other end rest against the Backrest Adjustment Bar (#32).

B.) Place the Backrest Board (#31) onto the Backrest Supports. Secure it with four M6 x 1 ½”

Hex Bolts (#46) and Ø ½” Washers (#41).

C.) Place the Seat Pad (#30) onto the Main Seat Support. Secure it with four M6 x 1 3/8” Hex

Bolts (#38) and Ø ½” Washers (#41).

DIAGRAM 4

8

«
...
7
8
9
10
11
...
»

Summary of Contents for MARCY MWB-36780B
















Reviews:

No comments

Related manuals for MARCY MWB-36780B

Brand: FOLLO FUTURA Pages: 16

Brand: Gregster Pages: 38

Brand: Powerhouse Fitness Pages: 26

Brand: Body Solid Pages: 10

Brand: WeiderPro Pages: 32

Brand: Horizon Fitness Pages: 15

Brand: Ironman Fitness Pages: 24

DRAFTER 550 PRO

Brand: ultega Pages: 38

Hammer Strength OHDMR

Brand: Hammer Strength Pages: 15

Brand: Assault Fitness Pages: 2

Brand: Assault Fitness Pages: 2

Brand: Ultimate Plate Pages: 7

Brand: Weider Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands