manualshive.com logo in svg

MPC 1250, Operator'S Manual, Page: 4 / 44

Share
Download
MPC 1250 Operator'S Manual Download Page 4

Section I 

Warnings

006-0007207 MPC-1250DC Guide  

Rev F 

4 of 44

 03/03/2022 

 

www.synqor.com

Section I 

Warnings

Hazardous Voltages

The  INPUT AND OUTPUT POWER connectors and cables of the SynQor MPC may have 

voltages that are unsafe. INJURY OR DEATH ON CONTACT may result. Appropriate safety 

precautions should be taken. All connections should be made in accordance with LOCAL 

ELECTRICAL CODES.
• The MPC CHASSIS should be connected to earth or system ground with Ground Stud on the 

rear panel, see mechanical diagrams.

• For the AC INPUT cable and connector:

▪  Do not assume that a hazardous voltage is not present at the terminals of the AC input 

connector, even if the MPC appears to be off.

▪  Do not make contact with the terminals of the AC input connector.
▪  Always connect the cable to the MPC before it is connected to the source of AC power. 
▪  Always disconnect the AC input cable from the source of AC power before disconnecting it 

from the MPC. 

▪ If the AC input cable is connected to the source of AC power and not connected to the 

MPC, do not contact the exposed terminals of the AC input cable.

▪  Do not assume that the source of AC power is not present.
▪ Connections between the AC input cable and the source of AC power should not be 

accessible.

• For the DC INPUT cable and connector:

▪  The rated DC input voltage of the MPC is below the level considered hazardous.
▪  The DC input terminals of the MPC are isolated from the AC input with reinforced safety 

insulation.

▪ However, never assume the terminals of the DC input connector or the wires of the DC 

input cable are safe to contact, even if the MPC or DC input source appears to be off.

• For the DC OUTPUT cable and connector:

▪  The rated DC output voltage of the MPC is below the level considered hazardous.
▪ The DC output terminals of the MPC are isolated from the AC input with reinforced 

safety insulation.

▪  However, never assume the terminals of the DC output connector or the wires of the DC 

output cable are safe to contact, even if the MPC appears to be off.

Summary of Contents for 1250













































Reviews:

No comments