manualshive.com logo in svg

MPC 1250, Operator'S Manual, Page: 23 / 44

Share
Download
MPC 1250 Operator'S Manual Download Page 23

Section III 

Operation

006-0007207 MPC-1250DC Guide  

Rev F 

23 of 44

 03/03/2022 

 

www.synqor.com

LEDs on the Front Panel - “Constant Current” Model

The “Constant Current” model has a 13 LED front panel display to indicate the status and 

operation of the MPC.

POWER OUT

POWER IN

LOAD

CHARGE

FAN

MPC

A0

C0

B0

B1

B2

B3

D0

D1

F0

E0

E1

E2

E3

Power-In Indicators (LEDs in positions D0 and D1)

The LED in position D0 indicates the status of the optional DC INPUT and the LED in position D1 

indicates the status of the AC INPUT, according to the table below:

LED Appearance

Description

Indication

Green

Input is Ready to Provide Load Power

Pulsing Green

Input is the One Presently Selected as the  

Source of Power

Amber

Input has Returned within Range and Diagnostic Tests are 

Being Performed

Off

Input is Not within Range 

Power-Out Indicator (LED in position A0)

The LED in position A0 indicates the status of the DC OUTPUT, according to the table below:

LED Appearance

Description

Indication

Green

MPC is On and the Output Voltage is  

Within Range

Amber

MPC is On but the Output Voltage is  

Out of Range

Red

MPC is Off and the Output Voltage is Within Range

Off

MPC is Off 

Summary of Contents for 1250













































Reviews:

No comments