MP Filtri ICM-ETHi User Manual Download Page 6 | Manualshive

Page: 6 / 14

background image

6

Lantronix Software Installation

3 Lantronix Software Installation

We supply a version of the software on CD, or the latest version from the Lantronix

web site can be used.
Run the CPR installer. This is a ﬁle with a name like ``setup_cpr_x86x64cd_4.3.0.0’’.

Accept the security warning and license.

Figure 1

The ``CPR Installer’’

The software requires the Microsoft .NET Framework. If you do not have this

already, the installer will ﬁrst install it for you. You will then need to restart the

computer and run the installer again to install the actual CPR program. Follow the

installation wizard accepting the defaults. You will need to accept another security

warning in order to install the Com Port driver software.

«
...
4
5
6
7
8
...
»

Summary of Contents for ICM-ETHi















Reviews:

No comments

Related manuals for ICM-ETHi

Brand: Ecco Pages: 4

Brand: JD Squared Pages: 15

Brand: DAPAudio Pages: 16

Brand: 3M Pages: 28

Brand: Taurus Pages: 28

Brand: Kärcher Pages: 54

Brand: ABB Pages: 85

Brand: Warehouse-lighting Pages: 3

Brand: E2S Pages: 5

Brand: Fenton Pages: 16

Brand: Velp Scientifica Pages: 16

Brand: Velp Scientifica Pages: 2

Brand: Velp Scientifica Pages: 32

Brand: Velleman-Kit Pages: 32

Brand: Tieline Pages: 359

Brand: MadLab Pages: 7

Brand: Kaiweets Pages: 6

Brand: Kaiweets Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands