Moyer Diebel 383HT Installation, Operation And Maintenance Manual Download Page 10 | Manualshive

Page: 10 / 32

Moyer Diebel 383HT Installation, Operation And Maintenance Manual Download Page 10

Installation

The installation of the dishwasher must comply with all local electrical, plumbing, health, and

safety codes or in the absence of local codes, installed in accordance with the applicable require-

ments in the National Electrical Code, NFPA 70, Canadian Electrical Code (CEC), Part 1, CSA

C22.1; and the Standard for Ventilation Control and Fire Protection of Commercial Cooking

Operations, NFPA 96.

Installation Codes

NOTE:

The installation of your dishwasher must be performed by qualified service personnel

familiar with food service equipment and must comply with all local health codes.

Problems due to improper installation are not covered by the Limited Warranty.

STOP

STOP

ALL PLUMBING CONNECTIONS MUST BE MADE

BEFORE

THE ELECTRICAL INSTALLATION.

DAMAGE TO THE WATER HEATERS WILL OCCUR IF POWER IS TURNED ON WITHOUT AN

ADEQUATE WATER SUPPLY.

DAMAGE DUE TO IMPROPER INSTALLATION IS NOT

COVERED BY THE LIMITED WARRANTY.

2

«
...
8
9
10
11
12
...
»

Summary of Contents for 383HT

































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands