Mountz PULSE TOOLS Page 45 Instruction Manual Download

Page: 45 / 50

Mountz Inc. 1080N 11

Street, San Jose CA 95112 Ph (408) 292-2214 Fax (408) 292-2733

www.mountztorque.com

Fig. 125



HOUSING AND MOTOR SET ASSEMBLY:

1.0 Housing and Air Inlet Assembly:

Install and tighten the parts of air inlet one by one and orderly. (NOTE: Apply the Loctite



on the

threads of air inlet before assembly)

2.0 Housing and Trigger Set Assembly:

Install the parts of the trigger set orderly (see Fig. 126 drawing for reference). Then, Insert the pin to fix

all the parts. And, install the hanger to complete the assembly.

3.0 Cylinder

Unit

Assembly

3.1

Place the rotor blades into the rotor. Insert the spring pin A and B into the cylinder. Make sure the

pins aim at the pin holes when putting the cylinder down.

Fig. 126

Spring pin B

Spring pin A

Rotor unit

Summary of Contents for PULSE TOOLS



















































Search results

Summary of Contents for PULSE TOOLS

Reviews:

Related manuals for PULSE TOOLS

Brands by name

Popular brands

Mountz PULSE TOOLS, Instruction Manual

Search results

Summary of Contents for PULSE TOOLS

Reviews:

Related manuals for PULSE TOOLS

Brands by name

Popular brands