manualshive.com logo in svg

MOULDPRO TCU-200, User Manualline

Share
Download
MOULDPRO TCU-200 User Manualline Download Page 31

 

 

 

 

[31] 

User Guidelines 

– TCU-200 

 

12-06-2019 

Vers. 003 

 

 

Fix the leakage problem, fixed the leakage  connect again the pump switch TCU unit will restart automatically. 

 

Another leak detection (designed for oil TCU units) is: 

 

If the process is more than 10 seconds in oil demand (this may be due  to a loss level in the TCU unit) 
because filling is manual and not  incorporating automatic filling in area A the message displayed will be 

 

 

 

Will activate the audible alarm by turning off the pump and heating temperature control unit. 

Once the user has disconnected the pump switch and confirmed the alarm by pressing   

 

  

 

Fix the leakage problem, fixed the leakage  connect again the pump switch TCU unit will restart automatically. 

 

 

10.1  Deactivate Leak monitoring 
 

If the user disables leak monitoring, the letter L (zone B) will not  appear. 

The alarm   will be 

disabled. 

 

Alarm                   can act, whether the process is water or oil but, pump  must be running in continues for 2 
minutes. 

 

 

Summary of Contents for TCU-200











































Reviews:

No comments

Brands by name

Popular brands

Load more brands