background image

This guide is provided as a help and not a total solution for every installation. 

Common sense and concern for customers equipment will make for a good installation. 

 

 

21

Use wire strippers to remove the sleeve around each wire, and the FOLD the wire back onto the sleeve as shown. (This 
makes a better connection). 
 

 

Using a small screwdriver, attach each wire to the green 9-Pin connector supplied. 
The connector is color coded so that each wire has a specific location to be secured into. 
 

RUNNING 12 VOLT

 – You will have to run a 2-conductor cable (supplied) from a 12-volt source (

2 Amp Minimum, 3 Amp is 

preferred)

 to the main controller.   This power line should not be connected to the ignition where it can be turned off.  It 

should always be on (such as an accessories socket) for safety reasons. Use a voltmeter to make sure that you have found 
a Positive and Negative lead. 

NEVER connect to a circuit that supplies power to a light fixture. 

 

 

 

                                                                       

 

 

 

 

 

 

MANUALLY MOVING THE DISH 

 
WARNING – 

Make sure that you remove the 9-Pin Control Cable Connector from the back of the main controller 

BEFORE you put a power source to the dish control wires or you WILL damage the circuitry on the main controller. 

 

Bk Br Rd Or Yl Gn Bl Wh Pr

Improper wiring can 
cause damage to the 
DataStorm electronics 
(in the Mount as well as 
in the Controller).  Be 
alert!

Bk = Black 
Br = Brown 
Rd = Red 
Or = Orange 
Yl = Yellow 
Gn = Green 
Bl = Blue 
Wh = White 
Pr = Purple 

+12v     Ground     *Ignition

 

Stow 

   9 

to 

36 

VDC

 

Minimum Voltage 

 
12 Volts DC 
2.0 Amp 
 

Improper voltage 
can cause system 
failure. 

*Ignition Stow 

 
This pin will stow the dish, 
if it is up, when 9 to 36 
Volts DC is applied.  Find a 
DC Voltage source that is 
present when you want the 
dish to stow itself and wire 
it to this position. 

3 Pin Green Connector 

Summary of Contents for DataStorm




























Reviews: