manualshive.com logo in svg

Motorola V600, Service Manual, Page: 36 / 56

Share
Download
Motorola V600 Service Manual Download Page 36

36

 

       October 10, 2003  

6809468A79-O

Disassembly

 V600

Removing and Replacing the Flip CLI Lens Assembly

1.

Remove the battery cover, battery, SIM, antenna, rear housing, and 
transceiver board assembly and flip assembly as described in the procedures.

2.

Remove the flip assembly cover (see Figure 14a).

3.

Remove the 4 flip assembly screws (see Figure 14b). Be careful not to loose the 
flip cover latches attached to 2 screws near the flip assembly hinge. Set the 
screws and latches aside for re-use.

4.

Release the 2 latches on each side of the flip assembly (see Figure 14).

5.

Disconnect the CLI flex connector from the flip assembly PCB located under 
the CLI lens assembly.

6.

Lift the CLI lens assembly away from the flip assembly.

Figure 14. Removing the Flip CLI Lens Assembly Part 1

Flip Assembly Cover

Flip Assembly CLI Lens

A

Flip Cover Latch

Flip Cover Screws

Flip Cover Screws

Flip DIsplay Flex

CLI Lens Assembly

B

Summary of Contents for V600

























































Reviews:

No comments