Motorola V600 Service Manual Download Page 27 | Manualshive

Page: 27 / 56

Motorola V600 Service Manual Download Page 27

6809468A79-O

October 10, 2003

27

Level 1 and 2 Service Manual

Disassembly

3.

Using the disassembly tool, release the housing latch on each side of the phone
as shown in Figure 6.

4.

Carefully lift the rear housing away from the front housing and flip assembly.

5.

To replace, carefully align the rear housing to the front housing and the flip
assembly, then press the rear chassis assembly down until the 2 housing
catches engage with the corresponding openings on the rear chassis assembly.
Press the housings together until the catches snap into place.

6.

Replace the 4 transceiver screws and tighten to a torque setting of 1.5 inch
pounds. Do not over tighten.

7.

Replace the antenna, SIM, battery, and battery cover as described in the
procedures.

031638o

Figure 6. Removing the rear housing

G

The flip assembly and the front housing can also be removed at this point in the
disassembly procedure.

Rear Housing Latch

Rear Housing

Disassembly Tool

«
...
25
26
27
28
29
...
»

Summary of Contents for V600

























































Reviews:

No comments