Motorola EX-3524 Installation Manual Download Page 34

Page: 34 / 36

EX-3524/EX-3548 Layer 2 Gigabit Ethernet PoE/PoE+ Switch

Motorola Solutions Support Center

If you have a problem with your equipment, contact support for your region.

Contact information is available at:

https://portal.motorolasolutions.com/Support/US-EN

When contacting Motorola Solutions support, please provide the following information:

• Serial number of the unit

• Model number or product name

• Software type and version number

Motorola Solutions responds to calls by e-mail, telephone, or fax within the time limits set forth in support
agreements. If you purchased your product from a Motorola Solutions business partner, contact that business
partner for support.

Customer Support Web Sites

The Motorola Solutions Support Central Web site, located at

https://portal.motorolasolutions.com/Support/US-EN

provides information and online assistance including developer tools, software downloads, product manuals and
online repair requests.

Manuals

https://portal.motorolasolutions.com/Support/US-EN/WNetworks

General Information

Obtain additional information by contacting Motorola Solutions at:

Telephone (North America): 1-800-722-6234

Telephone (International): +1-631-738-5200

Website:

http://www.motorolasolutions.com

Summary of Contents for EX-3524





































Search results

Summary of Contents for EX-3524

Reviews:

Related manuals for EX-3524

Brands by name

Popular brands

Motorola EX-3524, Installation Manual

Search results

Summary of Contents for EX-3524

Reviews:

Related manuals for EX-3524

Brands by name

Popular brands