Motorola EX-3524 Installation Manual Download Page 19

Page: 19 / 36

Installation Guide

3.4 Port Connections

3.4.1 Installing SFP Transceivers

The switch provides slots for optional (not provided) SFP transceivers. The supported transceiver types are listed
below:

•

1000BASE-SX

•

1000BASE-LX

•

1000BASE-LH

•

1000BASE-FX

•

1000BASE-T

To install a SFP transceiver:

Consider network and cabling requirements to select an appropriate transceiver type that is also
compatible with the switch transceiver support.

If the SFP slot is covered with a rubber protective cap, remove the cap and keep it for later replacement.

Insert the transceiver with the optical connector facing outward and the slot connector facing down. Note
that SFP transceivers are keyed so they can only be installed in the correct orientation.

NOTE

SPF transceivers are hot-swappable. The switch does not need to be powered off
before installing or removing the transceiver.

Summary of Contents for EX-3524





































Search results

Summary of Contents for EX-3524

Reviews:

Related manuals for EX-3524

Brands by name

Popular brands

Motorola EX-3524, Installation Manual

Search results

Summary of Contents for EX-3524

Reviews:

Related manuals for EX-3524

Brands by name

Popular brands