Motorola DCT700 Installation Manual Download Page 35

Page: 35 / 46

Diagnostics B-11

DCT700 Installation Manual

d 06: Firmware Version

This diagnostic displays the:

Dena firmware version or revision number

Build date and time

TSODA firmware version number

CAMEL (CMLBK) firmware version number (always 0000)

The BOOT is the lowest level of firmware code that can be used on the DCT700.

FIRMWARE VERSION

02.06

BOOT 02.03

Oct 6, 2003

19:18:46

TSODA t16

CMLBK 0000

d 07: Current Channel Status

This diagnostic displays the instantaneous status of the last attempted channel tune on the

in-band tuner. It shows the channel type (analog/digital), acquisition state, purchasable

indicator, preview indicator, parental control status, and mute status.

CURRENT CHANNEL STATUS

TYPE DIGITAL

aaa bb

STATUS ccccc

dddd CONNECTED

PREVIEW NO

CURR

PURCHASABLE NO

PURCHASED NO

EPOCH NUM

0X0

EPOCH TYPE

0x0

AUTH 0X0

0X0

SERVICE 0 STATUS 1 ID 0X0004 0X00

CH 204 TUNED FREQ 543.000

Summary of Contents for DCT700















































Search results

Summary of Contents for DCT700

Reviews:

Related manuals for DCT700

Brands by name

Popular brands

Motorola DCT700, Installation Manual

Search results

Summary of Contents for DCT700

Reviews:

Related manuals for DCT700

Brands by name

Popular brands